Konica Minolta bizhub 4050 - Manual (Page 3)

2
CAUTION
• If toner lands on your skin or clothing, wash thoroughly with soap and water.
• If you inhale toner, move to a place with fresh air and gargle with a lot of water repeatedly. Should you
get symptoms such as coughing, seek medical advice.
• If you get toner into your eyes, immediately rinse them with running water for over 15 minutes. Seek
medical advice if irritation persists.
• If you swallow toner, rinse out your mouth and drink a few glasses of water. Seek medical advice if
necessary.
• Whenever moving the printer, be sure to disconnect the power cord and other cables. Failure to do this
could damage the cord or cable, resulting in a fire, electrical shock, or breakdown.
• Unplug the printer if you are not going to use it for a long period of time.
• When moving the printer, always hold it as specified in the user documentation. If the printer falls, it
may cause severe personal injury and/or be damaged.
• Use the printer only in a well-ventilated location. Operating the printer in a poorly ventilated room for
an extended period of time could be harmful to your health. Ventilate the room at regular intervals.
• Remove the power cord from the outlet more than once a year and clean between the plug terminals.
Dust that accumulates between the plug terminals may cause a fire.
When using the machine, do not look at the light of the lamp for a prolonged time. Eyestrain could
result.
■ Regulation Notices
● GS Certification
This product is GS-certified for the KONICA MINOLTA branded model bizhub 4750 or bizhub 4050.
● Laser Safety
This product employs a Class 3B laser diode having maximum power of 12 mW and wavelength of 650-670 nm.
This product is certified as a Class 1 laser product per IEC 60825-1: 2007. Since the laser beam is concealed by protective
housings, the product does not emit hazardous laser radiation as long as the product is operated according to the instructions
in this manual.
● Internal Laser Radiation
Maximum average radiation power: 19.8 μW at the area of the photoconductor drum.
Wavelength: 650-670 nm
COMPLIES COMPLIES WITH WITH 21CFR 21CFR 1040.10 1040.10 AND AND 1040.11 1040.11 EXCEPT EXCEPT FOR FOR
DEVIATIONS DEVIATIONS PURSUANT PURSUANT TO TO L LASER ASER NOTICE NOTICE NO. NO. 50, 50, DATED DATED JUNE JUNE 24, 24, 2007. 2007.
CAUTION:
Use of controls, adjustments, or performance of procedures other than those specified in this manual may result in
hazardous radiation exposure.
● Interference-Causing Equipment Standard (ICES-003 ISSUE 5)
- For Canadian Users
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device must be used with a shielded interface cable.
The use of non-shielded cables is likely to result in interference with radio communications and is prohibited under ICES-
003.
● FCC Part 15 - Radio Frequency Devices
- For United States Users
FCC: Declaration of Conformity
Product Type Multifunction Printer
Product Name bizhub 4750, bizhub 4050
Options FS-P02, PF-P11, PF-P12, DK-P02, MK-P03, FK-512, EK-P04, LK-106, LK-107, LK-108, LK-
111, KP-P01, SK-501, AU-201
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
WARNING:
The design and production of this unit conform to FCC regulations, and any changes or modifications must be registered
with the FCC and are subject to FCC control. Any changes made by the purchaser or user without first contacting the
manufacturer will be subject to penalty under FCC regulations.
This device must be used with a shielded interface cable.
The use of non-shielded cables is likely to result in interference with radio communications and is prohibited under FCC
rules.
● For European Users
This product complies with the following EU directives:
2004/108/EC, 2006/95/EC, 2009/125/EC and 1999/5/EC
This declaration is valid for the areas of the European Union (EU) or EFTA only.
This device must be used with a shielded interface cable.
The use of non-shielded interface cables is likely to result in interference with radio communications and is prohibited
under 2004/108/EC rules.
● Ozone Release
During print operation, a small quantity of ozone is released. This amount is not large enough to harm anyone adversely.
However, be sure the room where the machine is being used has adequate ventilation, especially if you are printing a
high volume of materials, or if the machine is being used continuously over a long period.
● Dégagement d’ozone
En cours de fonctionnement, l’imprimante ne dégage qu'une faible quantité d’ozone, insuffisante pour provoquer un
quelconque malaise personnel. Veillez cependant à ce que la pièce dans laquelle la machine est installée soit aérée de
manière adéquate, notamment si vous imprimez de gros volumes ou si l'imprimante est longtemps utilisée en continu.
● Electromagnetic Interference
This product must be used with a shielded interface cable.
The use of non-shield cables is likely to result in interference with radio communications and is prohibited under CISPR
22 and local rules.