Pioneer BDP-51FD User Manual
Page 52
07
52
En
Picture is stretched.
Aspect ratio cannot be
switched.
Is the TV’s aspect ratio properly set?
Read the TV’s operating instructions and set the TV’s aspect
ratio properly.
Is
4:3 Video Out properly set?
• Set
4:3 Video Out properly (page 41).
• When video signals with a resolution of 1080/50i, 1080/50p,
720/50p, 1080/24p, 1080/60i, 1080/60p or 720/60p are being
output from the
HDMI OUT terminal or the COMPONENT
VIDEO output terminals, they may be output with an aspect
ratio of 16:9 even if
TV Aspect Ratio is set to 4:3 (Standard)
(page 24).
Sound and picture are not
synchronized.
Is
Output Terminal Priority properly set?
Set
Output Terminal Priority properly (pages 19 and 49).
Picture is disturbed during
playback.
Picture is dark.
• This player supports Macrovision analog copy protection
technology. With some TVs (such as with built-in video deck),
the picture will not be displayed properly when the copy
protected DVD title is played. This is not a malfunction.
• If the player and TV are connected via a DVD recorder/video
deck, etc., the picture will not be displayed properly due to
analog copy protection. Connect the player and TV directly.
No picture is displayed or
picture is not output in high
definition when playing BDs.
With some content protected discs, it may not be possible to
output the video signals from the
VIDEO output terminals, the
S-VIDEO output terminal or the COMPONENT VIDEO output
terminals. In this case, connect using an HDMI cable
(page 13).
No sound is output.
Sound is disturbed.
Is the disc played back in slow motion?
Is the disc played back in fast forward or fast reverse?
No sound is output during slow motion play and forward and
reverse scanning.
Is the disc scratched?
The sound may not be output if the disc is scratched.
Is the disc dirty?
Clean the disc (page 60).
Is the player properly connected to the other components (AV
receiver or amplifier, etc.)?
• Check that you connect the player to the audio output
terminals of a different component, etc.
• Check that you connect the player to the PHONO input
terminals of the AV receiver or amplifier, etc.
Are the connected components (AV receiver or amplifier, etc.)
properly set?
Read the operating instructions of the connected components
and check the volume, input, speaker settings, etc.
Are the audio cables properly connected?
Insert the cables firmly and all the way in.
Is the audio cable damaged?
If the cable is damaged, replace it with a new one.
Is the player connected to the TV using an HDMI cable to watch
the picture?
When connecting using component video cables, an S-Video
cable or a video cable to watch the picture, it is not possible to
listen to the sound of devices connected with HDMI cables.
Take one of the measures below (pages 13 and 16).
– To watch the picture on a device that is not HDMI
compatible, connect using either an optical digital audio
cable, coaxial digital audio cable or analog audio cables
(7.1 or 2 channels) to listen to the sound.
– To listen to the sound on an HDMI-compatible device,
connect to the TV using an HDMI cable to watch the
picture.
After one of the above measures, use Setup Navigator to reset
the player (page 19).
Is
Audio Output Mode properly set?
If
Audio Output Mode is set to Multi-channel, the audio
signals may not be output properly from the
AUDIO OUT (2
ch) terminals (page 41). Set Audio Output Mode to 2
Channel.
Are the speakers properly set?
Set
Speaker Setup properly (page 41).
For some BDs, audio signals are only output from the
DIGITAL
OUT (COAXIAL/OPTICAL) terminal or the HDMI OUT
terminal.
Problem
Check
Remedy
51FD_WV_EN.book 52 ページ ２００８年８月２６日 火曜日 午前９時５８分