Warning, 3 chipper blades (con't), 4 air filter – Echo 76824 Owners Manual v.3 User Manual
Page 20
![background image](/manuals/553273/20/background.png)
16
TURNTABLE CHIPPER
SERVICE & MAINTENANCE
BEFORE INSpECTINg OR SERvICINg ANy pART OF ThIS MAChINE, ShUT OFF pOWER SOURCE,
DISENgAgE ThE hyDRAULICS, OpEN ShIELD AND MAkE SURE ALL MOvINg pARTS hAvE COME TO A COMpLETE STOp.
Warning
5.3.2 sharPening The blades
Never sharpen or grind the mounting surfaces of the blades.
This will cause the edge to roll and the blade will be damaged,
resulting in poor chipping performance.
Regrind the angled edge of the chipping blades to 45 degrees
(Figure 5.3).
The blades can be ground on a bench grinder or by a pro-
fessional.
Make sure some type of fixture is used to correctly hold the
blade at the proper angle.
Be careful when grinding so that the blade does not become
overheated and change color. This will remove the heat-
treated properties.
Use short grinding times and cool with water or some type
of liquid coolant.
Remove an equal amount off each blade to maintain disk
balance.
Small imperfections such as nicks and burrs on the flat side
of the blade will not affect the chipping performance of the
machine.
For blades that have been repeatedly sharpened, ensure
that the sharpened surface extends past the chipping slot
opening. If it does not extend past the opening, the blades
should be replaced.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Figure 5.3 - Chipper Blade Surfaces
MOUNTING SURFACE
DO NOT GRIND
MOUNTING SURFACE
DO NOT GRIND
SHARPENED
SURFACE
SHARPENED
SURFACE
45˚
.38
5.3.4 SETTINg ChIppER BLADE CLEARANCE
The chipping blades should clear the chipper block located di-
rectly under the chipper chute by 1/16 to 1/8 inch (Figure 5.4).
To adjust the blade clearance, proceed as follows:
Remove the two 3/8" bolts securing the access cover to the
main frame. Tilt access cover over to allow access to anvil
Loosen the three 1/2 inch bolts that hold the chipper anvil
to the frame.
Measure the amount of clearance between chipping blades
and chipping anvil from inside of housing. Adjust inward or
outward to desired measurement.
Check clearance on all the blades.
Tighten bolts on chipping anvil to 75 Ft-lb and resume op-
eration.
If chipping anvil edge is damaged or worn unevenly, remove
the three bolts holding the anvil and use one of the other
three edges. Adjust for correct measurement.
1.
2.
3.
4.
5.
6.
5.3.3 insTalling The blades
Install the disk lock (section 5.2). The disk is now restrained
for installing the blades.
place a blade on the disk and attach with two hex head
bolts and nuts. Torque to 120 Ft-lbs. Repeat for remaining
blades.
Lower the access cover and secure to the chipper housing
using two 3/8" retaining bolts.
Remove disk lock.
1.
2.
3.
4.
5.3 chiPPer blades (con'T)
Figure 5.4 - Chipper Blade/Anvil Clearance
Refer to the engine owner's manuals included with your machine
for specific instructions on replacing and cleaning the air filter.
5.4 air filTer
- PAS ARTICULATING HEDGE CLIPPER ATTACHMENT PAS-2601
- 670-200
- PE-2000 Type 1/1E
- X7502026001
- SB
- PAS RAPID LOADER 99944200610
- 99944200610
- SRM-261SB
- SRM-210SB
- PAS-230
- PAS-230
- PAS-230
- PAS-260
- PAS-261
- 2410 - Type 2E
- GT-201
- POWER PRUNER PPT-2400
- HC-155
- HC-155
- Trimmer
- SRM - 265U
- HC-150
- HC-235
- HC-225
- BLADE CONVERSION KIT 231
- TC-2100
- SRM-400
- SRM - 260S
- 54
- HCA-2400
- CULTIVATOR PRO ATTACHMENT 99944200513
- RM-5000
- SRM-265T
- SHC-210
- 2110
- PE-3100 Type 1/1E
- SRM-265S
- SRM - 230U
- SRM-225I
- 99944200553
- 99944200553
- BRUSHCUTTER
- 99944200615
- PAS RAPID LOADER 99944200615
- 99944200485
- 99944200485
- SHAFT HEDGE CLIPPER HCA-265
- TRIMMER ATTACHMENT PAS-230
- TC-2100 Type 1
- HC-185
- HC-165
- SRM-210i
- SHC-260
- SRM-225SB
- SRM-211
- GT-251E
- SRM-280S
- HC-245
- HC-2410
- SRM-3800 TYPE1-E
- GT-2000
- SRM - 410U
- SRM - 410U
- GT-2000R
- GRASS/WEED TRIMMER BRUSHCUTTER and CLEARING SAW
- TC-210
- HC-1500 Type 1E
- SRM-265
- SRM230
- GT-2000EZR
- HCA-265
- SRM-260
- Power Blend TC-210
- CULTIVATOR TC-210I
- SHC-225 Serial S85312002871 - S85312999999
- GT-230
- GT-230
- SHC-265
- SRM-280T
- GT-200 R
- SRM-2305
- 99944200540
- 99944200540
- SRM - 230S
- SRM - 230S
- HC-150I
- SRM-2400SB EN
- PAS-2601 EN
- ES-2100
- CLS-5800
- PAS-225
- BRD-280 Serial S70711001001 - S70711002517
- BRD-280 Serial S70711002518 - S70711999999
- PB-760LN
- PB-755SH
- PB-265LN
- PB-255LN
- PB-250LN
- SRM-280U Serial S67511001001 - S67511006177
- SRM-280U Serial S67511006178 - S67511007612
- SRM-280U Serial S67511007613 - S67511999999
- SRM-266U
- SRM-225U Serial S79111001030 - S79111999999
- SRM-225U Serial S79111001001 - S79111001029
- SC3342
- 71110
- 70487
- 70252 v.1
- LS27
- CHF9540HXE
- CHF9540H Owners Manual v.6
- CHF9540H Owners Manual v.5
- CHF9540H Owners Manual v.4
- CHF9540H Owners Manual v.3
- CHF9540H Owners Manual v.2
- CHF9540H Owners Manual v.1
- CHF9540H Instruction v.4
- CHF9540H Instruction v.3
- CHF9540H Instruction v.2
- CHF9540H Instruction v.1
- CH9540H Owners Manual v.1
- CH9540H Instruction v.7
- CH9540H Instruction v.5
- CH9540H Instruction v.1
- CH922DH Owners Manual v.7
- CH922DH Owners Manual v.6
- CH922DH Owners Manual v.5
- CH922DH Owners Manual v.4
- CH922DH Owners Manual v.3
- CH922DH Owners Manual v.2
- CH922DH Owners Manual v.1
- CH922DH Instruction v.8
- CH922DH Instruction v.5
- CH922DH Instruction v.4
- CH922DH Instruction v.2
- CH8993H Owners Manual v.7
- CH8993H Owners Manual v.6
- CH8993H Owners Manual v.5
- CH8993H Owners Manual v.4
- CH8993H Owners Manual v.3
- CH8993H Owners Manual v.2
- CH8993H Instruction v.6
- CH8993H Instruction v.5
- CH8993H Instruction v.3
- CH8993H Instruction v.2
- CH8720iH Owners Manual v.2
- CH8720iH Owners Manual v.1
- CH8670HXE
- CH800H Owners Manual v.3
- CH800H Owners Manual v.2
- CH800H Owners Manual v.1
- CH6993H Owners Manual v.4
- CH6993H Owners Manual v.3
- CH6993H Owners Manual v.2
- CH6993H Owners Manual v.1
- CH6993H Instruction v.7
- CH6993H Instruction v.5
- CH6993H Instruction v.4
- CH6730HXE Instruction v.2
- CH6730H Instruction v.2
- CH6720H Instruction v.2
- CH6614H Owners Manual v.4
- CH6614H Owners Manual v.3
- CH6614H Owners Manual v.2
- CH6614H Owners Manual v.1
- CH611DH Owners Manual v.6
- CH611DH Owners Manual v.5
- CH5653 Owners Manual v.2
- CH5653 Owners Manual v.1
- CH5540H Owners Manual v.4
- CH5540H Owners Manual v.3
- CH5540H Owners Manual v.2
- CH5540H Owners Manual v.1
- CH5540H Instruction v.2
- CH5540 Owners Manual v.2
- CH5540 Owners Manual v.1
- CH4614 Owners Manual v.2
- CH4614 Owners Manual v.1
- CH45540 Owners Manual v.5
- CH45540 Owners Manual v.4
- CH45540 Owners Manual v.3
- CH45540 Owners Manual v.2
- CH45540 Owners Manual v.1
- CH45540 Instruction v.4
- CH45540 Instruction v.2
- CH450H Owners Manual v.2
- CH450H Owners Manual v.1
- CH4400 Owners Manual v.2
- CH4400 Owners Manual v.1
- CH4400 Instruction v.2
- CH123DH Owners Manual v.2
- CH123DH Owners Manual v.1
- CH123DH Instruction v.2
- CH123DH Instruction v.1
- 7812086 Owners Manual v.3
- 7812086 Owners Manual v.2
- 77454 Owners Manual v.5
- 77454 Owners Manual v.4
- 77454 Owners Manual v.3
- 77454 Owners Manual v.1
- 76835 Owners Manual v.1
- 76824 Owners Manual v.1
- 76635 Owners Manual v.3
- 76635 Owners Manual v.2
- 76635 Owners Manual v.1
- 76628S
- 74824 Owners Manual v.3
- 74824 Owners Manual v.2
- 74824 Owners Manual v.1
- 74800 Owners Manual v.4
- 74800 Owners Manual v.2
- 74800 Owners Manual v.1
- 74628S Owners Manual v.2
- 74628S Owners Manual v.1
- 74628 Owners Manual v.2
- 74628 Owners Manual v.1
- 74628 Instruction v.2
- 74554 Owners Manual v.3
- 74554 Owners Manual v.2
- 74554 Owners Manual v.1
- 73454 Owners Manual v.3
- 73454 Owners Manual v.2
- 72942 Owners Manual v.4
- 72942 Owners Manual v.2
- 72928S
- 72928 Owners Manual v.6
- 72928 Owners Manual v.5
- 72825 Owners Manual v.4
- DSRM-200
- PE-280 Serial S63111001001 - S63111006135
- PE-280 Serial S63111006136 - S63111999999
- PE-266S
- PE-230 Serial 03001001 - 03999999
- PE-230 Serial 05011201 - 05999999
- PE-230 Serial 05001001 - 05011200
- PE-230 Serial 06001001 - 06999999
- PE-230 Serial S68311001001 - S68311999999
- PE-225 Serial S78611002140 - S78611999999
- PE-225 Serial S78611001001 - S78611002139
- HC-152
- SHC-225 Serial S85312001001 - S85312002870
- SHC-266
- HCA-266
- 99944200563
- 99944200620
- 99944200535
- 99944200595
- 99944200513
- 99944200470
- 99944200470
- 99944200600
- 99944200465
- PAS-225VPB
- PAS-225VP
- PAS-225VP
- PAS-225SB
- PAS-280
- PAS-266
- PPT-280 Serial E08011002238 - E08011999999
- PPT-280 Serial E08011001001 - E08011002237
- PPT-266
- ES-255
- ES-250
- TC-210 Serial 05001001 - 05999999
- TC-210 Serial E13912001001 - E13912999999
- MS-53BPE
- MS-41BP
- MS-21H
- SRM-280T Serial S66711001001 - S66711008029
- SRM-280T Serial S66711008030 - S66711011609
- SRM-280T Serial S66711011610 - S66711999999
- SRM-266T
- GT-225i
- GT-225i
- DL8390 Owners Manual v.4
- DL8390 Owners Manual v.3
- DL8390 Owners Manual v.2
- DL8390 Owners Manual v.1
- DL8390 Instruction v.2
- DL8390 Instruction v.1
- DL12725 Instruction v.2
- DL12720 Owners Manual v.2
- DL12720 Owners Manual v.1
- DL12720 Instruction v.3
- 75124
- 73725
- 73724
- LS33340T Owners Manual v.5
- LS33340T Owners Manual v.4
- LS33340T Owners Manual v.3
- LS33340T Owners Manual v.2
- LS33340T Owners Manual v.1
- LS33340T Instruction v.2
- LS33340T Instruction v.1
- LS33340 Instruction v.8
- LS33340 Instruction v.7
- LS27 Owners Manual v.2
- LS27 Owners Manual v.1
- LS27 Instruction v.11
- LS27 Instruction v.8
- LS27 Instruction v.5
- LS27 Instruction v.3
- SG340 Owners Manual v.4
- SG340 Instruction v.2
- SG340 Instruction v.1
- SG340 Instruction v.3
- 73711S Owners Manual
- WT24T Owners Manual
- WT24T Instruction v.2
- WT24T Instruction v.1
- WT24 Owners Manual
- WT24 Instruction v.2
- WT190T Owners Manual v.4
- WT190T Owners Manual v.3
- WT190T Owners Manual v.2
- WT190T Owners Manual v.1
- WT190T Instruction v.2
- WT190T Instruction v.1
- WT189 Owners Manual
- 76065 Owners Manual v.2
- 76065 Owners Manual v.1
- 74455S
- 74455 Owners Manual v.3
- 74455 Owners Manual v.2
- 74455 Owners Manual v.1
- PAS 80 Tooth Blade Brushcutter
- PAS Rapid Loader
- PAS Articulating Hedge Clipper Attachment 99944200590
- GT-225
- SRM-210
- SRM-225
- SRM-225