Tweco 300 Ultra-Cut User Manual
Page 49
Advertising
Manual No. 0-4819 Ultra-Cut 300
3-25
INSTALLATION
Installation
The Remote Arc Starter must be installed in a suitable location near the torch head.
If the Arc Starter is mounted
to a gantry or to any other support subject to motion or vibration, fasten the Arc Starter to the support securely.
1. Loosen, but do not remove, the lower screws securing the cover to the Arc Starter. Remove the upper
screws securing the Cover Panel to the Arc Starter.
NOTE
The cover is grounded to the Arc Starter base through a wire shown below. This wire must remain in
place.
2. Remove the Cover Panel from the Arc Starter.
Art # A-09625
Lower screws
(2 per side)
Upper screws (2 per side)
Cover
Ground Wire
Advertising
See also other documents in the category Tweco Equipment:
- PAK 200i
- 211i Fabricator
- 15C Drag-Gun LT
- AirCut 15C
- TD-750 Cutting Systems
- TD-750 Cutting Systems
- 6000 Cutting System
- 100 Auto-Cut
- 100 Auto-Cut
- Auto-Cut 100 Torch Operation
- 200 Auto-Cut
- 300 Auto-Cut
- C-20A CUTSKILL
- C-35A CUTSKILL
- C-70A CUTSKILL
- 15XC CE Merlin PAK
- 6000 CE Merlin
- Merlin 6000 Plasma Cutting CE Slave Power Supply
- 6000GST Merlin Plasma Cutting CE Slave Power Supply
- 150XL CE PAK Master Without Latch Circuit
- CutMaster 101
- CutMaster 101 with SL100SV
- CutMaster 10mm
- CutMaster 10mm-12mm
- CutMaster 12mm-20mm-25mm
- CutMaster 12mm
- 151 CutMaster
- 151 with SL100SV
- 151 with SL100SV
- 152 CutMaster
- 15mm Cutmaster
- 20mm Cutmaster
- 25mm Cutmaster
- CutMaster 35mm 40mm
- CutMaster 35mm
- 38 CutMaster
- 38 CutMaster
- 39 CutMaster
- 42 CutMaster Operating Manual
- 42 CutMaster Service Manual
- 50 CutMaster
- 51 CutMaster
- 51 with SL100SV CutMaster
- 102 Cutmaster
- 82 PlazMaster
- 82 PlazMaster
- 81 CutMaster
- 81 with SL100SV
- 82 CutMaster
- A120 CutMaster
- A40-A60 CutMaster
- A40 CutMaster
- A80-A120 CutMaster
- A80 CutMaster
- 35A CutSkill Power Supply and SL40 Torch EU version
- 35A CutSkill
- 35A CutSkill Power Supply
- C-100A CutSkill
- C-20C CutSkill
- C-35C CutSkill
- Drag-Gun
- 220 VAC 50Hz Drag-Gun
- 35C Drag-Gun Plus
- GC-3000 Gas Control
- GCM-6000 Gas Control
- Grounding For Mechanized Systems
- HE-150 Coolant Recirculator
- 6000GST Cutting Systems
- 1000 Cutting Systems
- 6000 Cutting Systems
- 300 Maximizer
- Max 300 w-Merlin 3000
- Max 300 w-Merlin 6000
- Max 300 w-Merlin 6000GST
- Max 300 w-TD-750
- Maximizer 300 Torch for BNFL
- 1000 Merlin(Dec2004)
- 1000 Merlin(Sept1999)
- 15XC Merlin
- 3000 Merlin
- Merlin 6000 Master PS
- Merlin 6000 Slave PS
- Merlin 6000GST Master PS
- PAK 15XC
- PAK 10
- Pak 200
- PAK 44G
- PakMaster 100XL Plus
- CE PAK Master 150XL With Latch Circuit
- CE PAK Master 150XL Without Latch Circuit
- PAK Master 150XL
- PakMaster 50XL Plus (CE)
- PakMaster 50XL Plus
- PakMaster 75XL Plus (CE)
- PakMaster 75XL Plus
- PC250
- PC250
- PCH - 102 Hand Torch
- PCH-62 Hand Torch
- PCH-62 Hand Torch
- PCH-120 Hand Torch
- RAS used w-Merlin 6000GST
- RC6010
- SC-3000
- SC-3000
- SC-6 Standoff Control
- SL60
- SL60
- SC10
- SC11
- TA 500
- 100 Ultra-Cut
- 150 Ultra-Cut
- 150 Ultra-Cut
- 200 Ultra-Cut
- 400 Ultra-Cut
- Weld Sequencer
- XTTM-300
- XTTM-301
- 100 Ultra-Cut XT Plasma Cutting System
- 200 XT Auto-Cut 400V
- 200 XT Auto-Cut 480V
- 200 XT Auto-Cut 380V
- 300 XT Auto-Cut 380V
- 300 XT Auto-Cut 400V
- 300 XT Auto-Cut 480V
- Dynamics Automation
- 102 Cutmaster
- 10mm Cutmaster
- 40mm Cutmaster
- A60 Cutmaster
- iCNC XT
- 100 Ultra-Cut(March 2013)
- 100 Ultra-Cut(May 2014)
- 200 Ultra-Cut(March 2013)
- 300 Ultra-Cut(March 2013)
- 400 Ultra-Cut(March 2013)
- 100 XT Ultra-Cut Plasma Cutting System
- 100 Ultra-Cut Plasma Cutting System with Automated Gas Control
- 100 Ultra-Cut(October 2014)
- 200 XT Ultra-Cut Plasma Cutting System
- 200 XT Ultra-Cut Plasma Cutting System With Automated Gas Control
- 300 XT Ultra-Cut Plasma Cutting System
- 300 XT Ultra-Cut Plasma Cutting System With Automated Gas Control
- 400 XT Ultra-Cut Plasma Cutting System
- 400 XT Ultra-Cut Plasma Cutting System With Automated Gas Control
- K3000
- Tri-Arc Serie
- SLICE
- N7500
- 141i Fabricator
- 181i Fabricator
- 252i Fabricator
- 161 S Inverter Arc Welder
- 161 S Inverter Arc Welder
- 161 S UK
- 161 STL Thermal Arc
- 201 ts Thermal Arc
- 186 AC Inverter
- 300 AC Arcmaster
- 95 S Thermal Arc(Jan2013)
- 95 S Thermal Arc(Nov2010)
- 160 S Arcmaster
- 160 TS Arcmaster
- 175 TE Arcmaster
- 200 ACDC Arcmaster(Feb2006)
- 200 ACDC Arcmaster(April2006)
- 300 ACDC Arcmaster
- 300 MST Arcmaster
- 300 S Arcmaster
- 300 TS Arcmaster(Feb2006)
- 300 TS Arcmaster(April2006)
- 400 MSTP Arcmaster
- 400 TS Arcmaster
- Auto Darkening Welding Helmet
- 6045 Excel Arc
- 140 Portable MIG
- 181i Thermal Arc Fabricator
- 186 AC/DC Thermal Arc
- 190 MIG Thermal Arc Fabricator
- 210 MIG Thermal Arc Fabricator
- 211i Thermal Arc Fabricator
- 251 Thermal Arc Fabricator
- 281 Thermal Arc Fabricator
- 2460 Heavy Duty CC CV Control Wire Feeder
- Hefty II CC CV Voltage Sensing Wire feeder
- HMC-410
- HMC-410 Robotic Interface Kit
- 185TSW AC CC
- VS 212 PortaFeed
- VS 212 PortaFeed
- 320SP PowerMaster
- 350 PowerMaster
- 400SP PowerMaster Automation
- SP SERIE PowerMaster
- PWH-M 2A
- Raider 10,000 Pro
- SP 2001 Spool Gun
- CE Ultima 150
- Ultima 150
- A 2000 Ultra-Feed
- VA 2000 Ultra-Feed
- VA 4000 Ultra-Feed
- VA 4000S Ultra-Feed
- WC 1 Weld Sequence Controlle
- 400 MST Arc Master
- 130i Transarc Operating Manual
- 130i Transarc Service Manual
- 170i Transarc
- 170Pi Transtig
- 170Ti Transtig
- 175i Transtig
- 175i Transtig
- 200AC Inverter Arc Welding Machine
- 350 Weldskill MIG
- 250 4R Wirefeeder
- 250i Transmig Inverter
- 300Pi Transtig Welding Inverter
- ProPlus Digital Auto-Darkening Welding Helmet
- VS212 Wire Feeder
- 200i Multi Process Welding Inverter
- 250i Multi Process Welding Inverter 2RT Wire Feeder
- 350i Transmig
- 400i Transmig
- VAF4 Transmig
- VAF4HD Transmig
- 2RT Transmig
- 100 Weldskill
- 170 HF Weldskill
- Cigweld WeldSkill Auto Darkening Welding Helmets
- FP-125 Mini MIG Portable MIG Welder
- FP-100
- FP-120
- FP-125 Mini MIG
- FP-200
- FP-20A
- FP-35A
- FP-38 Power Supply
- FP-55
- FP-70A
- FP-82
- FP-90
- FP-95 Mini MIG
- PC-500
- PC-800
- Spool Gun Firepower