Tweco XT-301 Torch Data for Distributor Use w-Auto-Cut 100 AD User Manual
Page 2
Torch Data
8-2
Manual 0-4733 Rev. AD
Ohmic Sensing
Ohmic sensing is not recommended with water shield. Water on the plate interferes electrically with the ohmic
sensing circuit.
Direction of Cut
The plasma gas stream swirls as it leaves the torch to maintain a stable arc column. This swirl effect results in one
side of a cut being more square than the other. Viewed along the direction of travel, the right side of the cut is more
square than the left.
Right Side
Cut Angle
Left Side
Cut Angle
A-00512
Scrap
Clockwise
Counter-
Clockwise
Art # A-04182
Workpiece
Scrap
Side Characteristics Of Cut
To make a square - edged cut along an inside diameter of a circle, move the torch counterclockwise around the circle.
To keep the square edge along an outside diameter cut, move the torch in a clockwise direction.
Underwater Cutting
Cutting on a water table either underwater or with the water touching the plate or with a water muffler system is not
recommended. If a water table is used the water level must be a minimum of 4 inches / 100 mm from the bottom of the
plate. Failure to follow this recommendation could result in poor cut quality and short consumable parts life.
- Mini MIG Guns 160 Amp
- ArcMaster 401MST
- ArcMaster 401S
- Eliminator Spool Gun
- Fabricator 252i
- Lightweight Quick Robotic Torch
- QCT-1
- QFA600
- QRC-2000
- QRM-100
- QRM-3 Anti-Spatter Sprayer
- QRP-IN TCP Check Tool
- Quick Fixed
- Quick Robotic Torch
- QWT-120
- QWT-3 Quick Wire Trim Unit
- RDM-2000
- SprayMaster with Velocity Consumables MIG Gun
- 181i
- 211i
- Fabricator 141i Operating Manual
- Fabricator 141i Quick Start
- Victor Torch Handles,Cutting Attachments
- Single & Two Stage Regulators
- 7-3431
- 7-3436
- 7-3437
- 7-3438
- 7-3439
- 7-3440
- 7-3441
- 7-3442
- 7-3443
- 7-3444
- 7-3445
- 7-3446
- 7-3448
- 7-3449
- 7-3450
- 7-3480
- 7-3482
- 9-1001
- 9-8311
- 9-9385
- 9-9417
- 9-8587
- 9-0203
- 9-9515
- 9-9435
- 9-9408
- 7-4000
- 7-3360
- 9-9488
- 8-3441
- RAS-1000 Remote Arc Starter
- 7-3460
- SL100 RPT
- SL55 Plasma Cutting
- 7-5225
- SL80 Plasma Cutting
- 9-9430
- M-42 RPT
- 9-8418
- Torch Data for Auto-Cut O2 V.1
- Torch Data for Auto-Cut O2 V.2
- 100 Torch
- 9-9436
- Troubleshooting Power Supply
- Ultra-Cut Torch Data
- XT 301 Torch
- XT-300 Torch Data for Distributor Ultra-Cut 150 & 200 Power Supply AJ
- XT-300 Torch Data for Distributor UltraCut-100 AG
- XT-300 Torch Data for OEM Ultra-Cut 150 & 200 Power Supply AJ
- XT-300 Torch for OEM UC-300
- XT-300 Torch for OEM UltraCut-100 AG
- XT-301 Torch Data for Distributor Use w- Auto-Cut 200 AF
- XT-301 Torch Data for Distributor Use w- Auto-Cut 20 O2 AG
- XT-301 Torch Data for Distributor use w- Auto-Cut 30O2 AE
- XT-301 Torch Data for OEM Use w- Auto-Cut 100 AD
- XT-301 Torch Data for OEM use w- Auto-Cut 30O2 AD
- 4-3054
- Torch Data AutoCut
- XT-301 Torch Data
- W4000001
- 9-7717
- Victor Thermal Dynamics Interface Cable
- Victor Thermal Dynamics Power Module Upgrade Kit
- 7-7500
- W4015104
- 7-3315
- Welding Equipment Basic Utility Cart
- W4016700
- W4016900
- W4016300