Craftsman 315.117260 - Manual (Page 3)

GENERAL SAFETY RULES
WARNING: Read and understand all
instructions. Failure to follow all instructions listed
below, may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
■ Keep your work area clean and well tit. Cluttered
benches and dark areas invite accidents.
■ Do not operate power tools in explosive atmo­
spheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
■ Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
ELECTRICAL SAFETY
■ Double insulated tools are equipped with a
polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a
qualified electrician to install a polarized outlet.
Do not change the plug in any way. Double insuia-
tion [O eliminates the need for the three-wire
grounded power cord and grounded power supply
system.
■ Avoid body contact with grounded surfaces such
as pipes, radiators, ranges, and refrigerators.
There is an increased risk of electric shock if your
body is grounded.
■ Don’t expose power toots to rain or wet condi­
tions. Water entering a power tool will increase the
risk of electric shock.
■ Do not abuse the cord. Never use the cord to
carry the tools or pull the plug from an outlet.
Keep cord away from heat, oil, sharp edges, or
moving parts. Replace damaged cords immedi­
ately. Damaged cords increase the risk of electric
shock.
■ When operating a power tool outside, use an
outdoor extension cord marked “W-A” or “W”.
These cords are rated for outdoor use and reduce the
risk of electric shock.
PERSONAL SAFETY
■ Stay alert, watch what you are doing and use
common sense when operating a power toot. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inatten­
tion while operating power tools may result in serious
personal injury.
■ Dress property. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, cloth­
ing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving
parts.
■ Avoid accidental starting. Be sure switch is off
before plugging in. Carrying tools with your finger
on the switch or plugging in tools that have the switch
on invites accidents.
■ Remove adjusting keys or wrenches before
turning the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result in
personal injury.
■ Do not overreach. Keep proper footing and
balance at ail times. Proper footing and balance
enables better control of the tool in unexpected
situations.
■ Use safety equipment. Always wear eye protec­
tion. Dust mask, nonskid safety shoes, hard hat, or
hearing protection must be used for appropriate
conditions.
■ Do not wear loose clothing or jewelry. Contain
long hair. Loose clothes, jewelry, or long hair can be
drawn into air vents.
■ Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
TOOL USE AND CARE
■ Use clamps or other practical way to secure and
support the workpiece to a stabie piatform.
Holding the work by hand or against your body is
unstable and may lead to loss of control.
■ Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed.
■ Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
■ Disconnect the plug from power source before
making any adjustments, changing accessories,
or storing the tool. Such preventive safety mea­
sures reduce the risk of starting the tool accidentally.
■ Store idle tools out of the reach of children and
other untrained persons. Tools are dangerous in the
hands of untrained users.
■ Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp
cutting edges are less likely to bind and are easier to
control.
■ Check for misalignment or binding of moving
parts, breakage of parts, and any other condition
that may affect the tool’s operation. If damaged,
have the tool serviced before using. Many acci­
dents are caused by poorly maintained tools.
■ Use only accessories that are recommended by
the manufacturer for your model. Accessories that
may be suitable for one tool, may become hazardous
when used on another tool.
■ Keep the tool and its handle dry, clean and free
from oil and grease. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleum-
based products, or any strong solvents to clean your
tool. Following this rule will reduce the risk of loss of
control and deterioration of the enclosure plastic.