Symtech Headlight Cleaner Kit - Manual

BRIGHT SOLUTION
HEADLAMP CLEANER / POLISH
Thank you for purchasing BRIGHT SOLUTIONS CLEANER
this is a 1 to 2 STEP process that takes approximately 10~15
MINUTES to perform per headlamp dependent upon severity of
damage of lamp lens.
KEEP OUT OF THE REACH OF CHILDREN
DO NOT ALLOW PRODUCT TO FREEZE
DO NOT APPLY IN DIRECT SUNLIGHT
READ INSTRUCTIONS IN ENTIRETY BEFORE USE.
USE ENCLOSED GLOVES TO PROTECT HANDS..
524 S.E. Transport Drive
Lee’s Summit, Missouri 64081
816-525-9263 FAX: 816-525-9383
www.symtechcorp.net
Safety by Design
SAFETY and HEALTH
WARNINGS
ALL PRODUCTS INCLUDED IN THIS KIT ARE ON
REVERSE SIDE
A
s with any repair versus replacement, some items will not
achieve like new results. If directions are followed,
significant improvement in the appearance of the items will
be achieved. As we are unable to supervise the application
process, user assumes all risks. The manufacturer and its
distributors are not liable for any damages incurred by the
use of this product. If you are unsure as to the application
process, or compatibility of the item you would like to
resurface, please contact the manufacturer, or distributor for
advise on how to proceed.
Can Be Used on : Headlamps Taillights
Turn Signal Lights Reflective Lens Covers
FIRST determine the extent of damage that has occurred over time to
your headlamp lens.
IF Headlamp lenses are slightly fogged and or yellowed,
without visible hairline scratches or crazing, in most cases
the lamp can be simply cleaned clear without the use of
sandpaper STEP 1.
IF Headlamp lenses have extensively yellowed, have scratches,
crazing and/or pits, sanding is necessary to obtain a
successful result STEP 1 (
OPTIONAL ). Regardless of
damage, using sandpaper during cleaning will speed the
process dramatically.
STEP 1
CLEANING
Remove all contents from package.
Select one of the towels and fold in quarters (1).
Thoroughly shake the BRIGHT SOLUTIONS HEADLAMP
CLEANER/POLISH before applying to towel. Shake the
container frequently throughout the cleaning process.
Open the specially formulated BRIGHT SOLUTIONS
HEADLAMP CLEANER/POLISH, saturate a small area of
the towel (2), and begin cleaning the entire lens with a circular
motion (3).
Continue cleaning, changing the towel surface and adding more
HEADLAMP CLEANER/POLISH as towel becomes
discolored (4) with dirt and oxidation film of lamp lens.
When dirt and discoloring ceases to be removed from lens, allow
cleaner to dry and buff to a high sheen (7).
STEP 1 (OPTIONAL)
SANDING / CLEANING
Empty contents of package and fill cavity of package with water (4), start
with 1500 grit sandpaper, dampen sandpaper with water (5) and
begin sanding the entire surface of the lens, wetting sandpaper (5) as
needed to prevent buildup of particles. Sanding is complete when
lamp lens is uniform in appearance.
Note: ALWAYS sand in a straight motion (6), DO NOT use a
circular motion.
Take the 2000 grit sandpaper and dampen (5), again sand the entire surface
of the lens, wetting sandpaper (5) as needed to prevent buildup of
particles. This process will reduce the sanding lines .
Note: ALWAYS sand in the same direction as previous step and
in a straight motion (6), DO NOT use a circular motion.
Select one of the towels and fold in quarters (1).
Thoroughly shake the BRIGHT SOLUTIONS HEADLAMP
CLEANER/POLISH before applying to towel. Shake the container
frequently throughout the cleaning process.
Open the specially formulated BRIGHT SOLUTIONS HEADLAMP
CLEANER/POLISH, saturate a small area of the towel (2), and
begin cleaning the entire lens with a circular motion.
Continue cleaning and polishing, adding more HEADLAMP
CLEANER/POLISH as necessary to polish the entire lamp lens
When lens has achieved a highly polished appearance, wipe off all polish
residue and buff to a high sheen (7)
3 2
6
1
7
4 5