Doepfer, System a-100, Usb/midi-to-cv/gate a-190-4 – Doepfer A-190-4 MIDI/USB-CV/Gate/Sync Interface User Manual
Page 5: Setting up the a-190-4
DOEPFER
System A-100
USB/Midi-to-CV/Gate A-190-4
5
3. Setting up the A-190-4
Before powering up your A-100 system, please use a
MIDI- or USB cable to connect your MIDI device to the
A-190-4:
• Connect the A-190-4’s MIDI IN socket to the MIDI OUT
socket of your MIDI device (master keyboard, MIDI
synth, MIDI sequencer, etc.).
Or: Connect the A-190-4’s USB port to your computer or
MIDI device. Your MIDI software / MIDI device should
automatically recognice the A-190-4.
• Now power up your System A-100. The A-190-4’s
display will show its operation software version
number for about one second (e.g. 101).
• Patch the outputs of your A-190-4 to corresponding
modules on the System A-100:
The
gate output (6) and CV1 output (7) are
connected to the system bus of the A-100 by
default, so don’t use patch cables to connect
them, unless you have disconnected the jumpers
JP2/JP3 (page 18) or you want to connect a third
party module which does not access the A-190’s
system bus (please refer to the note for using
more than one A-190-4). VCOs on the same
system bus automatically receive CV1, and
ADSRs automatically receive the gate signal.
Output
Connection examples
8 CV 2
Any module’s CV input (e.g. a VCF’s
CV input, for controlling the filter cutoff).
4
Clock
E.g. the A-160’s trigger input for MIDI-
synced sequences.
5 Reset The A-160’s reset input, for MIDI control
of start and stop messages;
The A-140’s gate or retrigger input for
MIDI-triggered envelopes.
Please note if you are using more than one
A-190-4:
The A-190-4 is usually connected to INT.CV und
INT.GATE on the system bus of the A-100 system.
If you want to run more than one A-190-4 with just a
single system bus, only one of the A-190-4’s must be
connected to the system bus.
Disconnect the other A-190-4 modules from the
system bus by disconnecting the two jumpers labelled
JP2 (CV bus) and JP3 (gate bus). Both jumpers are
located on the backside of the A-190-4 circuit board.
Please refer to page 19.
- DIY Synth do-it-yourself analog synthesizer
- MKE Universal Midi Keyboard Electronics Kit
- CTM64 Contact to Midi Interface (main board)
- CTM64 Relay Board
- MTC64 Midi to Gate Interface (main board)
- MTC64 Relay Board
- MTC64 Output Board (transistor driver board)
- MTC64 Power Board
- Pocket Electronic
- Dial Electronic
- Wheel Electronic
- USB64 Universal Midi and USB Controller Electronics Kit
- MBP25 Midi Bass Pedal Electronics Kit
- MTV16 Midi-to-Voltage Interface with 16 Analog Voltage Outputs
- A-100
- A-100AD5 +5V low cost adapter
- A-100(~ 40 MB)
- A-100CGK CV/Gate keyboard
- A-101-1 Vactrol Steiner Filter
- A-101-2 Vactrol Lowpass Gate
- A-101-3 Vactrol Modular Phase Filter
- A-101-9 Universal Vactrol Module
- A-102 Diode Low Pass
- A-104 four-fold Trautonium Formant Filter
- A-105 24dB SSM Low Pass
- A-106-1 Xtreme Lowpass/Highpass Filter
- A-107 Multitype Morphing Filter
- A-108 6/12/24/48 Formant Filter
- A-109 Voltage Controlled Audio Signal Processor
- A-110 Standard VCO
- A-111-1 High End VCO
- A-111-5 Synthesizer Voice
- A-112 Sampler/Wavetable Oscillator
- A-113 Subharmonic Oscillator
- A-114 Dual Ringmodulator
- A-115 Audio Divider
- A-116 VC Waveform Processor
- A-117 Digital Noise / 808 Source
- A-118 Noise/Random
- A-119 External Input/Envelope Follower
- A-120 24dB Low Pass 1
- A-121 12dB Multimode VCF
- A-123 24dB High Pass (no longer available)
- A-124 Wasp Filter
- A-125 VC Phaser
- A-126 VC Frequency Shifter (no longer available)
- A-127 Triple VC Resonance Filter
- A-128 Fixed Filter Bank
- A-129-1/2 Vocoder Basic Modules
- A-129-3/4 Vocoder Slew-Limiter/Attenuator/Offset and Controller
- A-129-5 Vocoder Voiced/Unvoiced Detector
- A-130/A-131 VCA (linear / logarithmic)
- A-132-1 Dual low cost VCA
- A-133 Dual Polarizer
- A-134 VC Panning
- A-135 VC Mixer
- A-136 Distortion/Waveshaper
- A-137-1 Wave Multiplier
- A-138 a/b Mixer (linear / logarithimc)
- A-138 c Polarizing Mixer
- A-139 Headphone Amplifier (no longer available)
- A-140 ADSR (Envelope Generator)
- A-141 VC-ADSR (VC Envelope Generator)
- A-142 VC Decay/Gate
- A-143-1 Complex Envelope Generator / Quad AD-Generator / Quad LFO
- A-143-2 Quad ADSR
- A-143-3 Quad LFO
- A-144 Morphing Controller
- A-145 LFO 1
- A-146 LFO 2 (variable Waveform)
- A-147 VC LFO
- A-148 Dual Sample&Hold
- A-149-1 Quantized/Stored Random Voltages
- A-149-2 Digital Random Voltages
- A-150 Dual VC Switch
- A-151 Quad Sequential Switch
- A-152 Voltage Addressed Track&Hold / Switch (Multiplexer) / Digital Outputs
- A-154 Sequencer Controller
- A-155 Analog/Trigger Sequencer
- A-156 Quantizer
- A-160 Clock Divider
- A-161 Clock Sequencer
- A-162 Dual Trigger Delay
- A-163 Voltage Controlled Divider
- A-165 Dual Trigger Inverter/Modifier
- A-166 Logic Module
- A-167 Analog Comparator / Offset Generator / Subtractor
- A-170 Dual Slew Limiter
- A-171 VC Slew Limiter
- A-172 Minimum/Maximum Selector
- A-174 Joy Stick
- A-175 Dual Voltage Inverter
- A-176 Triple Control Voltage Source
- A-177 External Foot Controller (no longer available)
- A-178 Theremin CV Source
- A-179 Light Controlled CV Source (no longer available)
- A-180 1x8/2x4 Multiple
- A-181 3.5/6.35 Multiple
- A-185 Bus Access
- A-188-1 BBD Module
- A-188-2 Tapped BBD Module
- A-190-1 MIDI-CV/Gate/Sync Interface
- A-190-2 MIDI-CV/Gate Interface
- A-191 Shepard Generator/16xMIDI-CV Interface (no longer available)
- A-192 CV to MIDI Interface
- A-196 PLL
- A-197 Analog Meter (no longer available)
- A-198 Trautonium / Ribbon Controller
- A-199 Spring Reverb
- A-100MNT Miniature Power Supply