Campbell Hausfeld WF2058 User Manual

Wire feed arc welder

Advertising
background image

Heat

Circuit Breaker or

Selector

Slow Blow Fuse

Low

15 amp

High

20 amp

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.

IN972800AV 11/04

Operating Instructions & Parts Manual

Models WF2050, WF2054, WF2057 & WF2058

Wire Feed
Arc Welder

BUILT TO LAST

Description

This Campbell Hausfeld welder is a 70
amp, single phase 115 volt input, wire
feed arc welding machine. This unit is
equipped with infinite wire speed control
to accurately select the proper wire feed
rate needed for various welding
conditions. Internal components are
thermostatically protected.

This welding system is designed for use
with the Flux Cored Arc Welding (FCAW)
process. As delivered from the factory,
this welder can weld with .030” (.8 mm)
or .035” (.9 mm) diameter flux-cored
wire. A starter spool of .035” (.9 mm)
wire is included.

Unpacking

All welding accessories for the
welder are inside the wire feed
compartment on side of welder.
When unpacking, inspect carefully for
any damage that may have occurred
during transit. Make sure any loose
fittings and screws, etc. are tightened
before putting unit into service. Report
any missing or damaged items by
calling 1-800-746-5641.

Circuit Requirements

This equipment
requires a dedicated

115 volt circuit. Refer to the following
chart for the correct circuit breaker or fuse
rating. Do not run other appliances, lights,
or tools on this circuit while operating
this equipment. Extension cords are not
recommended. Blown fuses and tripped
circuit breakers can result from failure to
comply with this recommendation.

!

CAUTION

General Safety

Danger means a
hazard that will

cause death or serious injury if the
warning is ignored.

Warning means a
hazard that could

cause death or serious injury if the
warning is ignored.

Caution means a
hazard that may

cause minor or moderate injury if the
warning is ignored. It also may mean a
hazard that will only cause damage to
property.

NOTE: Note means any additional
information pertaining to the product
or its proper usage.

Always keep a fire
extinguisher accessible
while performing arc
welding operations.

!

WARNING

!

CAUTION

!

WARNING

!

DANGER

See page 5 for supply cable
replacement instructions.

QU

AL

ITY

ASS

URANCE PR

OG

RA

M

Need

Assistance?

Call Us First!

1-800-746-5641

Components and Controls

1. Work Clamp - connects to work

piece.

2. Wire Feed Gun with .035” tip.

3. Power Cord - plug into 115 volt

outlet.

4. On/Off Switch.

5. Infinite Wire Speed Control - turn

clockwise to increase wire speed and
counterclockwise to decrease wire
speed.

6. Heat Selector - Selects welding

power. Two selections are possible;
low and high.

7. Light - illuminates if thermostat has

automatically shut off unit.

8. Wire Feed Compartment.

© 2004 Campbell Hausfeld/Scott Fetzer

For parts, manuals, product & service information

visit www.chpower.com

Figure 1 - Welder Components and Controls

1

2

3

4

5

6

7

8

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

Service Record
État de Service
Registro de servicio

Models WF2050, WF2054, WF2057 & WF2058

Modèles WF2050, WF2054, WF2057 & WF2058

Modelos WF2050, WF2054, WF2057 & WF2058

Wire Feed Arc Welder
Soudeur À L’Arc Alimenté En Fil
Soldadora Con Arco Con Alambre Continuo

Date
Date
Fecha

Maintenance performed
Entretien complété
Mantenimiento realizado

Replacement components required
Pièces de rechange exigées
Repuestos requeridos

Operating Instructions and Parts Manual
Manual de Instruccones y Lista de Repuestos
Instructions D’Utilisation et Manuel de Pièces

www.chpower.com

Advertising
This manual is related to the following products: