Kenmore 580.75116 - Manual (Page 6)

INSTALLATION
A CAUTION
We strongly recommend the removal of the
old wall sleeve and the installation of a new
Kenmore Wall Sleeve.
if you decide to keep the existing wail sleeve,
you have to redirect the louvers at the back of the
wall sleeve illustration. The use of piiers is
recommended. If you DO NOT redirect, you run
the risk of poor performance or product failure.
This is not covered under the terms of the
Kenmore warranty.
• Pick a location which will allow the conditioned air
to blow into the area you want. Good installation
with special attention to the proper position of the
unit will lessen the chance that service will be
needed.
ITEMS IN INSTALLATION HARDWARE
You may not need all parts in the kit. Discard
unused parts
ítem (Inches) Qty.
Plastic grille 263/4 X 16V2 1
Vertical insuiatlon strip 15S/16X 13/ b X 13/a1
Around Insulation Strips
67Ve X 1 X ^^/32 1
5927/32 X 13/s X 13/a 1
Horizontal Insulation Strip 237/32 X 13/B X 13/16 1
Support Block 1 ^/4 X 1 X 4^/16 2
Baffle 14 x 4'/2 X 1/6 1
Shim 11 13/16 X 1 X 3/4 2
Trim Frame 2
Washer Screw 4
Nuts(Plastlc) 4
Grille Rear 1
HOW i"0 INSTALL
EB identify the existing wall sleeve before installing
** the unit from the listed below.
Brand
Wail Sleeve Dimensions (inches)
Width Height Depth
White-Westinghouse
Frigidaire
Carrier (52F series)
25-1/2 15-1/4
16,17-1/2
or 22
Generai Electric
/Hotpoint
26 15-5/8 16-7/8
Whirlpool 25-7/8 16-1/2
17-1/8
or 23
Fedders/Emerson 27 16-3/4
16-3/4
or 19-3/4
Sears/Kenmore 25-7/8 15-17/32 16-23/32
Emerson/Fedders 26-3/4 15-3/4 15
Carrier (51S Series) 25-3/4 16-7/8 18-5/8
Friedrich 27 16-3/4 16-3/4
NOTE: All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition
and have a rear grille that securely attaches to
sleeve, or rear flange that serves as a stop for the
Air Conditioner.
Remove old air conditioner from existing wall
sleeve.
Clean the interior of an existing sleeve.
(Do not disturb seals.)
a Wall sleeve must be securely fastened in wall
before installing the air conditioner. Use the
nails or screws through sleeve into wall, if
needed. Repaint sleeve if needed.
Prepare the wall sleeve for installation of the
unit. If you plan to use your existing wall sleeve,
and it is not Kenmore, use procedure B or C
below.
Procedure Brand Depfh(mches)
A Sears/Kenmore 16-23/32
B
Wh ite-Westing house
Frigidaire Carrier
(52F series)
16,17-1/2
or 22
General Electric
/Hotpoint
16-7/8
Whirlpool 17-1/8 or 23
Carrier (51S series) 18-5/8
c
Fedders/Emerson
16-3/4
or 19-3/4
Emerson/Fedders 15
Friedrich 16-3/4
install new unit into wall sleeve.
CAUTION: When Installation Is completed,
replacement unit MUST have a rearward slope as
shown. To achieve 1/4" slope, remove the backing
from the 11-13/16" shim strips and attach them as
shown below in Fig. 3. Place the higher portion of
shim to the front of the rib on base of wall sleeve.
1 " highj^
Wall ibteava
FRONT
SHIM PLACEMENT UNfT INSTALLAHON
FIG. 3