Philips SBC MC600 - Manual

PHILIPS
Explanation of Controls
SBC MC600
B ^ English SBCMC600 (g|)
English
SBC MC600
Instructions for use
Mode d'emploi
Bedienungsanleitung
Istruzioni
Gebruiksaanwijzing
Instrucciones
Modo de emprego
Bruksanvisning
Käyttöohje
°l__
ol—Jo
<z>
Ro
«0
HIFI
Figure
03.5 MM
Mono JACK
KARAOKE SET
O
Figure 2
PHILIPS
SBC MC600
Figure
Instruction for use
1. Introduction
Congratulations! You have just bought a most sophisticated RF/FM wireless microphone system.This
system uses the latest RF/FM wireless technology to give you complete freedom of movement No more
inconvenience from cables and wires! To ensure you get the best performance from your RF/FM
microphone system, please read this document carefully.
2. Features
• Wireless transmission - the FM microphone transmits signals to the FM microphone receiver
without using any cables or wires.The FM microphone receiver is usually connected to a HiFi or
karaoke system.
• High-frequency radio system • the FM microphone set uses a high radio frequency as the signal
carrier, ensuring a very clear, sharp reception.
• No line of sight required - the FM microphone receiver is able to receive signals from the FM
microphone even if the line of sight is blocked by doors, walls, windows, or any moving objects.
• Up to 2 microphones operating at the same time • 2 FM microphone sets can operate in the
same room at the same time without interfering with each other.
• Non rechargeable system - the FM microphone operates on a 9 Volt non-rechargeable battery, and
the FM microphone receiver is powered by a l2VoltAC/DC power adapter.When the battery is
empty, simply replace it with a new battery and continue playing.There is no need to wait for the
battery to be recharged.
3. Components included
This FM microphone set contains the following components:
• FM microphone. SBC MC602
• FM microphone receiver. SBC MC605
• AC/DC adapter 12Volt / 200 mA. SBC 6654
• HiFi audio cable
• 9 Volt battery 6LR61 type. SM544
• 3.5 mm to 6.3 mm mono jack adapter
4. Explanation of Controls
FM microphone
1. Tuning control knob
2. Power ON/OFF switch
3. Power ON and Battery indicator LED
4. Channel selection switch (CH A / CH B)
FM microphone receiver
1. Tuning control knob
2. Power ON/OFF switch and Channel selection switch (CH A / CH B)
3. Power ON indication LED
4. Microphone signal output
5. DC power input
5. Installation
• Please ensure that the rated voltage of the AC/DC power adapter is the same as the mains power
supply before connecting the AC/DC power adapter to the mains power supply outleL
• Insert the DC connector of the AC/DC power adapter into the liVolt DC input located at the rear of
the FM microphone receiver, as shown in Figure I.
• Connect the microphone output located at the rear of the FM microphone receiver to the microphone
input of your HiFi or karaoke system using the HiFi audio cable, as shown in Figure I.
• Connect the 9 Volt battery to the battery snap inside the FM microphone and insert it into the battery
compartment, as shown in Figure II.
•When using 2 sets of FM wireless microphones in the same room at the same time, switch one of the
FM wireless microphone sets (i.e. microphone and receiver) to Channel B as shown in Figure III.The
preset channel is Channel A.
Operation
• Switch power of the FM microphone to ON: the power indication LED lights up. If the power indication
LED does not light, then the battery is empty and should be replaced.
Note: The preset channel is A by default. When using a second FM microphone set at the same time,
switch the second FM microphone to Channel B.
• Switch power of the FM microphone receiver to CH A or CH B: the power indication LED lights up.
The FM microphone receiver is turned ON power/channel selection switch is switched to either
Channel A [CH A) or Channel B (CH Bj.
Note: The preset channel of the FM microphone is A by default. When using only one FM micro
phone set. ensure that Channel A is selected for the FM microphone receiver. When using a second
FM microphone set at the same time, select Channel B for the second FM microphone receiver.
• Speak into the FM microphone and vary the tuning control on the FM microphone receiver until the
signal is at its clearest. You can fine tune the signal using the tuning control on the FM microphone.
White using the FM microphone, fine tuning may be required using the tuning control on the FM
microphone.
• Adjust the volume of your HiFi or karaoke system to an acceptable level.
7. Specifications
System
Carrier frequency
Modulation
Radiated output power
Effective transmission range
Microphone output level
Power supply - FM microphone
Power supply - FM microphone receiver
Frequency range (microphone)
Sensitivity (microphone)
Signal/Noise ratio
Distortion
Channel separation
: Radio Frequency (RF)
: Tunable
Channel A - 434.4 to 434.7 MHz
Channel B - 433.2 to 433.5 MHz
Frequency Modulation (FM)
0.5 m Watt
15 - 30 meter, omni-directional (360 )
8 mV
9 Volt battery
l2Volt/200 mA DC
80- 16.000 Hz
• 55 dB
>60dB
<0.5%THD
> 30 dB
Biliar*