Philips 7P6031C - Manual (Page 2)

ra S etup
AUTOMATIC S ettings
Thirst Time Setup automati-
JL cally takes care of some
basic TV control settings for
you. Follow the steps in this
section to quickly add area
channel numbers into the
TV's memory, and set the TV
for your connected signal
(Antenna or Cable.) You can
also set the TV's clock and
make connections for the
Picture-In-Picture feature as
well.
How TO U
se
F
irst
T
ime
S
etup
Press the MENU (M)
button on the remote or TV.
An on-screen list of TV fea­
tures shows on the screen -
"MAIN MENU".
■ HELP MENU
-8 1ST TIME SETUP
[
Installation
OPERATING TPS~ 8 For Problems
Of TV Features
The First-Time Setup
provides a simple method
of adjusting the most
important controls for
this television receiver.
Press 'M' To Continue
* Please Wait *
System is testing for
correct tuning mode.
Select "HELP" on the
TV's Main Menu. (Selected
MENU item is highlighted in
RED.)
Press the remote's Menu ^ ^
buttons to move UP/DOWN
and from SIDE-TO-SIDE
within the list of on-screen
features.
Press ADV(ance) A T and
(-F) (-) on the TV to move
UP/DOWN and from SIDE-
TO-SIDE within the list of
on-screen features.
Many of the current TV
control settings will be
modified by continuing
with First-Time Setup,
Press STATUS/EXrr to Quit
or
Press ”M" to Continue
<$>, Press MENU (M) on
the remote or TV to view the
HELP MENU.
1st Time Setup - Installation
(and other user help items)
will show on the TV screen.
Press MENU (M)T or
A on the remote (or ADV
TA on the TV) to select
"1ST TIME SETUP" (high­
lighted in RED).
Press "AT" to select the'
language you would like
the TV displays to use.
I ENGLIsiTI
SPANISH
FRENCH
Press ”M" to Continue
<l>
Press MENU (M) but­
ton on the remote or TV to
begin SETUP.
Follow the instructions
shown on the TV screen to
guide you through the First
Time Setup and use of your
new TV.
-------------------------- ^
Please check that yoi
antenna or cable is
connected to the plug
^marked ANT/CABLE on
the TV rear input panel.
Press STATUS/EXrr to Quit
or
Press "M" to Continue
This TV contains a clock
* Please Wait * which can automatically
Thè search for active be set through the
System is searching for
all active channels.
channels is complete. SMART CLOCK feature.
17 channels were found The clock will be set
Testing channel 2 to the time broadcast
in cable mode. by certain TV stations.
Press "M" to Continue
Press "M" to Continue
Do you want to set the
clock automatically?
SET TIME MANUALLY
Press "A T" to Select
Press "M" to Continue
Press "A T" to select the
time zone that you live in.
EASTERN
CENTRAL
MOUNTAIN
PACIFIC
ALASKA
HAWAII
Press "M" to Continue
Do you observe
Daylight Savings Time?
NO
Press "A T" to Select
Press "M" to Conbnue
The time is broadcast by
certain TV stations
System is looking for
time On channel 2.
We suggest trying PBS first
Enter the channel
Press "M" to Continue Please wait 45 seconds
Do you want to set the
clock automatically?
SET TIME AUTOMATICALLY
Press "A T” to Select
Press "M" to Continue
Please check TV clock and
adjust if necessary.
The time is currently
settoQ3 : 0(PM
Please enter current time
or
Press “M" to Continue
SMART CLOCK NOTE
• Set Time Automatically sets the clock according to TV
station Data Services Information: With this mode the clock
will automatically reset itself after power outages, and update itself
for Daylight Savings Time changes. Smart Clock will also reset itsell
every time the TV is turned off.
• Set Time Manually only allows you to enter the current time of
day and AM/PM settings.
Time was found
on channel 2.
The time is 12;00PM.
Press "M" to Continue
55=19==
This TV is equipped with
Picture-In-Picture (PIP)
Proper PIP operation
requires that a VCR must
be connected to the TVs
VCR/AUX inputs using
the method that follows.
Press ’M" to Continue
Connect a cable from the
VCR Video Out’ plug
to thelYELLQWIplug
marked VCR/AUX' on
the TV rear input panel,
Cahle has been r.nnnenteri
Press ”M" to Continue
Connect the Audio Cables
from the VCR 'AUDIO OUT
___ plugs to the
and IWHiH Plugs
marked VCR/AUX' on
the TV rear input panel.
Cable has been connected
Press ”M" to Continue
1
t
Please turn on the VCR,
PIP WINDOW
¥
This TV is equipped with
a Surround-Sound system.
insert a pre-recorded tape,
If you do not see the VCR
picture in the PiP window
Surround Sound requires
then press the 'PLAV
^ please check again that ^ the use of additionai
button on the VCR.
aii cables are properly speakers being placed
connected. around your room.
Now press "M" to view PIP
Press "M" to Continue
Press "M" to Continue
--------------------------- 1 ■ 1
PIP CONNECTIONS (REAR OF TV)
VIDEO CABLE
(YELLOW)
AUDIO CABLES
(RED AND WHITE)
-
©
REAR OF VCR
Please thoroughly read
the section in your
owners manual which
details the proper setup
and operation of the
Surround-Sound System.
if there is 1
fringe on the
use this ad
improve t
►
TED or BLUE
WHITE cross,
ustment to
ie picture.
Press "M"
-
Press"k
to Continue
Dr -
to Return
This completes the
First-Time Setup,
Press "M" to Exit Setup
S mart H elp
/ • Press the STATUS button on the remote or TV to stop
I — the SETUP at any time.
• When setting the Time Automatically, enter your local
~ PBS channel number.
• When setting the Time Manually use the remote's number (or
Menu AT) buttons to enter the time for the TV's clock. Use "0"
with single digit hour entries.
• Remember, SETUP is a first -use, one-time operation and will
not have to be repeated (only the clock settings can be lost).
2 - EL6238 E001