Winco 2-Wire Conversion Instructions PSS8B & PSS12H User Manual
Page 2
![background image](/manuals/716033/2/background.png)
225 SOUTH CORDOVA AVE
LE CENTER MN 56057
Phone: 507-357-6831
www.wincogen.com
8.
Reconnect the two black connectors; be sure to turn the locking rings on tight. But do not
over tighten or you will break the locking rings.
9.
Locate the small white 2 wire connector on the back end of the unit tie wrapped to the AC
harness running from the generator to the customer control box. This connector must be
plugged into the mating connector on the side of the new engine control. (This is a 120-Volt
signal for the stop crank relay inside the engine control. If it is not connected the starter will
never disengage and the unit will go into fault.)
10. Inside the DC portion of the customer connection box locate wire #22. Using the wire tag
#23 provided in the kit relabel wire #22 to #23.
11. Cover the 4-wire decal # 64576-011 on the backside of the customer connection box cover
with the 2-wire decal 64576-015. This is the new wiring instruction for connecting the unit to an
Automatic Transfer Switch. See New operators manual for addition wiring details.
12. Reinstall the cover on the connection box.
13. Locate the engine control description label just to the left of the engine control. A new label
has been provided with this kit, paste it over the existing label.
14. Remove the operators manual part number 60706-181 for model PSS8B4W from the
literature package and replace it with operators manual part number 60706-182 for Model
PSS8B2W. If you are working on a PSS12H4W remove manual 60706-183 and replace it with
manual 60706-184 for the PSS12H2W. These replacement manuals contain the proper infor-
mation for installation and operation of a 2-wire auto start system. The customer must have this
manual in order to start and operate the unit after the installation of the new engine control.
15 Reconnect the Negative battery cable if the battery is installed. Be sure the toggle switch
on the engine control is in the OFF position.
16. Replace the end panel.
17. Install the label “THIS UNIT HAS BEEN CONVERTED TO USE A TWO-WIRE START
ENGINE CONTROL” just below the engine control inside the enclosure.
18. Using the new operators manual, 60706-182 or 60706-184, this unit is now ready to be
installed as a standard 2-wire start system. This Generator set will now work with any transfer
switch that provides a ‘dry’ relay closure for a start/run signal
If you encounter any problems or need assistance,
feel free to contact the WINCO Service Department
at 507-357-6831
60710-121-8336-00
- Rotating Field Design Troubleshooting Guide
- Rotating Armature Design Troubleshooting Guide
- W3000H
- WT3000H/C
- WT3000H
- WC5000H/D
- CSAW6010DEX/C
- W6010DE/F
- W6010DE/G
- WC10000VE
- WC10000VE/E
- WL12000HE
- WL12000HE/K
- WL18000VE/B
- WL18000VE/N
- WC3000H
- WC3000H
- 2-Wheel Dolly Kit Assembly Instructions (2013)
- 4-Wheel Dolly Kit Assembly Instructions For 6kW Gen-Sets
- 2-Wheel Dolly Kit Assembly Instructions
- WC10000VE Dolly Kit Assembly Instructions
- WC10000VE/E Dolly Kit Assembly Instructions
- WC10000VE/E Dolly Kit Assembly Instructions
- 4-Wheel Dolly Kit Assembly Instructions for 12kW Gen-Sets
- 4-Wheel Dolly Kit Assembly Instructions for WL18000VE
- 4-Wheel Dolly Kit Assembly Instructions for WL12000HE, WL18000VE, HPS12000HE/F (2013)
- 2-Wheel Dolly Kit Assembly Instructions for 5 KW thru 9 KW (except storm unit) (2013)
- DL5000H/D
- DL5000H/C
- CSADL6000I/E
- DL9000E
- LC SERIES
- ME5000V/A
- CSADL6000I/B
- CSADL6000I/C
- HPS6000HE/I
- HPS9000VE/E
- HPS12000HE/F
- HPS6000HE
- HPS12000HE
- HPS6000HE/E
- HPS6000HE/H
- PSS6HEE
- Fuel Shut-Off Solenoid Kit HPS6000HE/I & HPS9000VE/E (2013)
- Fuel Shut-Off Solenoid Kit HPS12000HE/F (2013)
- HP9000VE
- HD6010DEX/P
- AP3000
- PSS8000
- PSS8000/P
- PSS8.5/A
- PSS8B4W/A
- PSS8B2W/A
- PSS12H4W/A
- PSS12H2W/A
- 2-Wire Conversion Kit Instructions PSS8B4W & PSS12H4W
- PSS15B4W/A
- PSS15B2W/A
- PSS15B2W-4/A
- PSS8B4W/C
- PSS8B2W/C
- ULPSS8B4W/E
- ULPSS8B2W/E
- PSS12H4W/D
- PSS12H2W/D
- ULPSS12H4W/E
- ULPSS12H2W/E
- PSS15B4W/D
- PSS15B2W/D
- ULPSS15B4W/E
- ULPSS15B2W/E
- ULPSS20B4W/A
- ULPSS20B2W/A
- 2-Wire Conversion Instructions PSS15B
- 2-Wire Conversion Instructions ULPSS8B2W/E
- 2-Wire Conversion Instructions ULPSS12H2W/E
- 2-Wire Conversion Instructions ULPSS15B2W/E
- 2-Wire Conversion Instructions ULPSS20B2W/A
- PSS10H/A
- PSS10H/B
- PSS20000/E
- Woodward Electronic Governor Control Operators Manual
- PSS25000/A
- PSS20000LS
- ULPSS21/A WITH DSE 7110 ENGINE CONTROL
- ULPSS21/A WITH DSE 7310 ENGINE CONTROL
- ULPSS21/B WITH DSE 7310 ENGINE CONTROL
- ULPSS21/E WITH DSE 7310 ENGINE CONTROL (2014)
- ULPSS30/B WITH BASLER DGC-2020 ENGINE CONTROL
- ULPSS30/C WITH DSE 7110 CONTROL (2011)
- ULPSS30/D WITH DSE 7310 CONTROL (2011)
- ULPSS30/E WITH DSE 7310 CONTROL (2013)
- ULPSS60/A WITH BASLER DGC-2020 ENGINE CONTROL
- ULPSS60/B WITH DSE 7110 CONTROL (2011)
- ULPSS60/C WITH DSE 7310 CONTROL (2011)
- ULPSS60/D WITH DSE 7310 CONTROL (2014)
- PSS27LS/A
- PSS27LS/C
- PSSRA27LS
- PSS27LS/D
- PSS30/A (2009 to 2010) Four Door Version
- PSS50LS-*/A
- PSS50LS/C
- PSS50LS/D
- PSS50LS/F
- PSS80/A
- PSS50LS FUEL CONVERSION INSTRUCTIONS
- DGC-500 TO DGC-2020 ENGINE CONTROL
- DGC-2020
- DGC-2020
- DGC-2020
- DGC-2020
- DGC-2020
- DGC-2020
- RDP-110
- DGC-500
- DSE3000 Series
- DSE71xx Series
- DSE7200 Series
- DSE7200 Series
- DSE7000 Quick Start Guide
- DSE549 Remote Ennunciator
- DSE2548
- GM100
- SX460
- AS440
- AS480
- ACO3
- AR2
- ECO3
- ECP3-2LN/2 (Replaces ECO3)
- ECO28 Revision 32 2012
- MR2
- S15W-75 REV 5
- S16W
- S20F
- S20W
- S20W REV 4 7-2011
- AVC63-4A
- W10PTOS/A
- 12PTOC-3
- 25PTOC-3
- W15PTOS/C
- W15PTOS/D
- W15PTOS/E
- 35PTOC-3
- 35PTOC-3
- W85PTOS
- 2-WHEEL PTO TRAILER 25 THRU 75 KW
- TDM76
- TPH241
- 2FS Generators 2000 Watt Belt Drive
- ULTB4000C
- RP25/A
- RP25/B
- RP25/C
- RP80
- RP55W/480 VAC Receptacles
- MD25K/C
- MDS45
- MDS50
- MDS50R3/B
- MDS50E3/B
- MDS65
- MDS85R
- ASCO 165 4-Wire
- ASCO 165 2-Wire
- ASCO 300 D Design 30-230 Amp
- ASCO 300 E Design 260-400 Amp
- ASCO 300 G Design 1000-3000 Amp
- ASCO 300 H Design 600-1200 Amp
- ASCO 300 J Design 600 Amp
- ASCO 300 Accessory 11BG
- ASCO 300 Accessory 44 Strip Heater
- ASCO 300 Accessory 72A Serial Module
- ASCO 300 Accessory Connectivity Module
- ATS
- ATS
- EMERGENCY TRANSFER SERVICE KIT
- ZTX-RM Series 40-400 Amps
- EC6010DR/R
- EC6010DR/S
- EC18000/A
- EC18000VE
- ECV2510-3
- 1B20
- YLT6010DE