Generac Power Systems NP-40G User Manual
Service manual, Computer controlled variable speed rv generators
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- SAFETY
- NOTICE TO USERS OF THIS MANUAL
- REPLACEMENT PARTS
- SERVICE
- MANUAL
- Part 1 THE AC GENERATOR
- Magnetism
- Electromagnetic Fields
- Electromagnetic induction
- Alternating Current
- Alternating Current (Continued)
- Electrical Units
- Ohm’s Law
- Reactance in AC Circuits
- Why Variable
- Speed Control?
- Introduction
- Upper Fan Housing
- Upper Cooling Fan
- Permanent Magnet Rotor
- Rotor Hub
- Stator Retaining Ring
- Stator Assembly
- Stator Adapter
- Lower Fan & Flywheel
- Engine
- Stepper Motor
- The Genistor
- The CCG Circuit Board
- The CCG
- Dirt and Moisture
- Insuiation Resistance Testers
- Stator Leads
- Preparation for Tests
- Test Aii Stator Windings to Ground
- Test All Stator Windings to Ground (Continued)
- Test for Shorts Between Windings
- Results of Tests
- Cleaning the Generator
- Drying the Generator
- Introduction
- Stator Assembly
- Genistor
- Testing the Battery Charge Circuit
- Testing the Battery Charge Circuit (Continued)
- Testing the CCG Circuit Board
- Construction
- Components
- General
- Parts List for Exploded View of Sheet Metal
- Part 2 ENGINE MECHANICAL
- Introduction
- 4-Cycle Engine Theory
- Recommended Fuels
- Recommended Engine Oil
- Storage Instructions
- Engine Tuneup
- Exploded View of Engine Long Block
- Valve Components Removal
- Valve Components Removal (Continued)
- Valve Service
- Valve Service (Continued)
- Valve Components Installation
- Valve Components Installation (Continued)
- Adjusting Valve Clearance
- Rocker Arm Cover installation
- Section 2.3- PISTON, RINGS, CONNECTING ROD
- Section 2,3- PISTON, RINGS, CONNECTING ROD
- Piston (Continued)
- Connecting Rod
- Assembly and Installation
- Cylinder Service (Continued)
- General
- Crankcase Cover Removal
- Camshaft Removal
- Crankshaft Removal
- Camshaft Inspection
- Camshaft Inspection (Continued)
- Crankshaft Inspection:
- Compression Release Mechanism
- Installing the Crankshaft
- Installing the Camshaft
- Installing the Camshaft (Continued)
- General
- Recommended Fuel
- Evaporation Control Systems
- Air Cleaner
- Air Intake
- Fuel Filter
- General Information
- Description
- Carburetor Disassembiy
- Carburetor Disassembly (Continued)
- Cleaning and Inspection
- Adjustment
- Engine Speed
- Throttle Linkage Adjustment
- Carburetor Removal
- General
- Description
- Operational Check and Adjustment
- General
- CCG Circuit Board
- Stepper Motor
- Testing the CCG Circuit Board
- Stepper Motor Probiems
- Testing the Stepper Motor
- General Information
- Advantages of Gaseous Fuels
- Fuel System Components
- Vapor Withdrawal
- Important Considerations
- Important Considerations (Continued)
- Fuei Suppiy Lines
- Excess Fiow Vaive
- Gaseous Carburetion
- Leakage Testing
- General
- Parts List for Figure 1
- Adjustments
- The LP Gas Regulator
- Testing the Fuel Lockoff Solenoid
- Testing the Fuel Lockoff Solenoid (Continued)
- General
- Carburetion
- Carburetor Adjustment
- Carburetor Removal
- Disassembly and Reassembly
- Part 5
- ENGINE OIL & COOLING SYSTEM
- Introduction to Oil System
- Oil Flow
- Oil Pickup Screen
- Oil Pump
- Oil Pump (Continued)
- Crankshaft Oil Seals
- Pressure Relief Valve
- Breather Assembly
- Oil Sump
- Oil Filter Support
- General
- Generator Air Flow
- Air Flow into Generator Compartment
- Compensating for Restrictions
- Compensating for Restrictions (Continued)
- General
- How it Works
- General
- Circuit Board Connections
- Receptacle J1
- Receptacle J2
- Receptacle J3
- Introduction
- Battery (Continued)
- Start-Run-Stop Switch (SW1)
- Starter Contactor
- Introduction
- Ignition Cage Assembly
- Ignition Sensor
- ignition Moduie
- Ignition Module (Continued)
- Ignition Coii
- Summary of Operation
- Ignition Timing
- Testing the System
- General
- Oil Pressure Switch
- Oil Temperature Switch
- Oil Temperature Switch (Continued)
- General
- Remote Panel Cables
- Description
- Wiring Connections
- Part 7 TROUBLESHOOTING
- Problem 1- Priming Function Does Not Work
- Problem 2- Engine Will Not Crank
- Problem 3- Engine Cranks But Will Not Start
- Section 7,2- ENGINE DC CONTROL SYSTEM
- Section 7.2- ENGINE DC CONTROL SYSTEM
- Problem 5- Engine Starts Then Shuts Down After a Few Seconds
- Test 1- Check 15 Amp Fuse
- Test 3- Check Power to Fuel Pump
- Test 2- Check Power to Switch
- Test 4- Check Battery/Battery Circuit
- Test 5- Test Fuei Pump
- Test 6- Test Primer Switch
- Test 7- Check Wire 14A to Fuei Pump
- Test 8- Check Power Suppiy to Starter Motor
- Section 7,2- ENGINE DC CONTROL SYSTEM
- Test 8- Check Power Supply to Starter Motor (Continued)
- Test 9- Check Wire 56 Power to Starter Contactor
- Test 10- Check Engine Controlier Board Power Supply
- Test 11- Test Starter Contactor
- Test 13- Check Fuel Supply
- Test 12- Test Start-Stop Switch
- Test 14- Check Fuel Filter
- Test 15- Check Ignition Spark
- Test 16- Check Spark Plug
- Test 17- Check ignition Power Suppiy
- Test 18- Check ignition Sensor
- Test 19- Check ignition Coii
- Test 20- Test ignition Moduie
- Test 21- Check Engine Controiier Board Output to Wire 14
- Test 22-Test Automatic Choke
- Test 23- Check Carburetion
- Test 24- Check Engine
- Test 25- Isolate the CCG System
- Test 26- Test Oil Pressure Switch
- Test 27- Test CCG System
- Section 7,2- ENGINE DC CONTROL SYSTEM
- Part 8
- SPECIFICATIONS AND CHARTS