Weston Cuber/Tenderizer Grinder Attachment - Manual (Page 4)

-4- -9-
GENERAL SAFETY RULES
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS
AND WARNINGS PRIOR TO USING THIS PRODUCT.
YOUR SAFETY IS MOST IMPORTANT! FAILURE TO
COMPLY WITH PROCEDURES AND SAFE GUARDS
MAY RESULT IN SERIOUS INJURY OR PROPERTY
DAMAGE. REMEMBER: YOUR PERSONAL
SAFETY IS YOUR RESPONSIBILITY!
WARNING!
SAVE THESE INSTRUCTIONS!
Refer to them often and use them to instruct others.
1. NEVER REACH INTO the Cuber/
Tenderizer. Doing so could cause serious
injury. ALWAYS USE THE PROVIDED
TONGS.
2.
DO NOT push the Tongs or other utensils
into the Blades.
3. NEVER use fingers to scrape food away
from the Cuber/Tenderizer while the grinder
is in operation. SEVERE INJURY MAY
RESULT.
4.
KEEP FINGERS CLEAR OF THE BLADES
AT ALL TIMES. Failure to do so may result in
personal injury. The Cutting Blades/Blade
Assembly is very sharp. It is recommended
to wear Kevlar, cut resistant gloves when
handling the Blades.
5. DO NOT press or push meat into the Chute
with your fingers or any other object. Doing
so may cause personal injury and/or damage
to the unit.
6. NEVER LEAVE THE Cuber/Tenderizer
UNATTENDED. Be safe, DISCONNECT the
Grinder from power source before leaving the
work area. Close supervision is necessary
when any appliance is used near children. This
appliance is NOT to be used by children.
7. FOLLOW ALL MANUFACTURER’S
INSTRUCTIONS AND SAFETY GUIDELINES
for operating the grinder.
8. NEVER use any accessories or parts from
other manufacturers. Doing so will VOID YOUR
WARRANTY and may cause fire, electrical
shock or injury.
9. Thoroughly clean all parts that will come
into contact with food before using the
Tenderizer/Cuber. Wash all parts by hand
and dry thoroughly. WARNING! Protective/
cut-resistant Kevlar gloves are recommended
when handling the blade assembly.
10. DO NOT attempt to tenderize meat with
bones or other hard items. Damage to the
machine will occur.
DISASSEMBLY & CLEANING INSTRUCTIONS
1. ALWAYS disconnect the grinder from the power source
before attempting to disassemble or clean the Cuber/
Tenderizer.
2. Keep children at a safe distance from unit while cleaning or
operating.
3. Remove the Cuber/Tenderizer from the grinder.
4. Remove the Combs from the Top Housing by lifting up on Combs. Figure 6
5. Remove the two Thumbscrews from the Top Housing. Set aside.
6. Remove the Top Housing. WARNING! This will expose the Cutting Blades.
Always wear cut-resistant gloves when handling the Blade assembly.
7. Using the provided
Allen Wrench, remove the Screws to remove Chute from
the Top Housing. Set the Screws and Lock Washers aside.
8. Carefully lift the Blade Rack Assembly from the Lower Housing.
9. Wash all parts thoroughly with warm,
soapy water. Rinse with clear water. A
long bristle brush is recommended for
cleaning the Blade Rack Assembly.
Always wear cut-resistant gloves when
handling the Blade assembly.
10. Dry thoroughly before re-assembling.
NOTE: It is highly suggested to coat all
metal parts with a food-grade silicone spray
(sold separately) to prevent corrosion.
11. TIE BACK loose hair and clothing, and roll
up long sleeves before operating the Cuber/
Tenderizer. REMOVE ties, rings, watches,
bracelets, or other jewelry before operating the
Cuber/Tenderizer.
12.
WEAR EYE PROTECTION. Wear safety
glasses. Everyday eye glasses are not safety
glasses. Safety glasses conform to ANSI Z87.1
requirements. Note: approved safety glasses
have Z87 printed or stamped on them.
13. DO NOT use outdoors.
14. DO NOT use the Cuber/Tenderizer while
under the influence of drugs, medications or
alcohol.
Combs
Top Housing
Lower Housing
Thumbscrew
Thumbscrew
Blade Rack
Assembly
Chute
Electric Grinder
Adapter
Figure 6
WARNING! Before cleaning, assembling or disassembling the Cuber/
Tenderizer Attachment make sure the PLUG of the GRINDER IS REMOVED
FROM THE OUTLET/POWER SOURCE! ALWAYS unplug the grinder when
not in use.