Nexen TCC-10 835141 User Manual
Page 7
![background image](/files/762898/content/doc007.png)
4
FORM NO. L-20069-E-0210
Q.D. (TAPER BORE) ROTOR HUB ASSEMBLY
FIGURE 7
FIGURE 8
Please verify that you are in the correct rotor section for
your model. This is the Q.D. Taper Bore Rotor Hub section.
The instructions for the Straight Bore Rotor Hub are in the
previous section.
REFER TO FIGURES 7-8.
1. Thoroughly inspect the tapered bore of the splined
hub and the tapered surface of the Q.D. bushing.
Remove any dirt, grease, or foreign particles. Do
not use any lubricants for this installation. Align the
untapped holes in the bushing with the tapped holes
in the hub and assemble the Q.D. bushing into the
splined hub.
2. Insert the pull-up bolts with Lock Washers into the
Q.D. bushing and hub and then alternate as you
tighten them evenly to the recommended torque
(See Table 2).
TABLE 2 Tightening Torques
Model
Bushing
Tightening Torque
TCC-10
JA
5 ft-lbs [6.7 Nm]
TCC-14
SK
15 ft-lbs [20.2 Nm]
TCC-20
J
135 ft-lbs [182.2 Nm]
CAUTION
Do not use lubricants or thread locking
compounds on these bolts or they may
tighten beyond the limits noted in Table
2 and the splined hub may burst.
CAUTION
The tightening force on the pull-up bolts
is multiplied by the wedging action of the
tapered surface. Do not tighten beyond
the limits noted in Table 2 or the splined
hub may burst.
3. Place the Key in the shaft keyway, slide the rotor
assembly onto the motor shaft.
4. Alternate as you evenly tighten the pull-up bolts to
the recommended torque (See Table 2).
5. Use a Dial Indicator to minimize run-out as you
tighten the Q.D. bushing pull-up bolts. To measure
run-out, place the contact tip of the Dial Indicator on
the machined surface of the Rotor. Maximum run-out
must be less than 0.007" [18 mm].
6. Use the Cap Screws (Item 18) and the Lock
Washers (Item 19) to fasten one-half of the Caliper
and Friction Facing assembly to the flange side
of the Housing (Item 8) at each caliper position.
Tighten the Cap Screws to 7 ft-lbs [9.5 Nm]
Cap
Screw
(Item 18)
Caliper
Half
Lock
Washers
(Item 19)
Housing
(Item 8)
Dial
Indicator
- RPS20 966611
- RPS20 966753
- RB15B 968179
- RBR25 960613
- RLSSB 150-063-C-A 966304
- SBPA02 964621
- SBP02 964610
- SBP04 964828
- SBP07 965008
- BSB02 964640
- HG17 969000
- HGP17 969011
- RPS4014G-B0192T/023-EP2U 966725
- RPS20G-C0140T/072-EP2U 966705
- RPS25G-B,C0064T-EP1 966950
- PRD1500 966903
- PRD400 966904
- I300 965500
- MTL300-ECC-SP-32MM-20MM-150/240 976131-225
- MDU-625 928600
- MDO-1375 936400
- Micro 856802
- B-275 802871
- F-450 802850
- BWB 846800
- XHW 810905
- FMCE-625 801487
- FMCE-130-19 801673
- 5H50PSP-E 913044
- 5H20P-E 911319
- 5H50PSP 912509
- 5H50P 910305
- 5H30P-E 913008
- 5H100PSE-E 913123
- 5H60P-E 913058
- 5H40S 911320
- 5H40S 911320
- 5H60PSP-SE 910440
- 3-Way Valve 948809
- LSCC-54 923578
- TL80 911785
- 4H70P 921700
- DPB 15T 963900
- DPB-15T 963002
- DPB 11T 961900
- QFE-2500 964097
- DFC-2200 964164
- DFC-1650 964161
- Electronic Over Load Protection System Controller 964404
- TL-15 801808
- TL60A-E 802948
- S-1400 822522
- T-1000A 824305
- S-1000A 828109
- SSE-1000 827700
- SSE-1400 822721
- SSE-1000 822573
- QFB-2500 964026
- BD 933703
- BD 933617
- BD 933900
- BC425S 835275
- QFB-2200 964098
- DB 835009
- 1000 Puck Caliper 837000
- DBSE 835036
- SPC 837472
- 12K Hinge Top 845700
- K Brake 843700
- VC500 837451
- 12K 845500
- EMB 230-38 965305
- FMBES-1375 827304
- SE-1000 812800
- MB-800 801352
- LSCB-54 923593
- BCB 826070
- FCB-450 827151
- FMCBES-8-42 801405
- MWCB 848000
- 500 Input Unit 801366
- 500 Input Unit 801366
- FMCBE-8-42 801640
- FMCBE-1375 801651
- Quick Exhaust Valve 945125
- Overlap Eliminators 944400
- Smart Valve 964508
- MBU-1375 935902
- FMCBE-875 BISSC 827263
- TL 70 - 80 Dual Pressure System 801577
- DAP 875 883100
- SSE-800 826300
- TL 80 801573
- FMCB-1625 801742
- HW 847200
- 5H60-SE-E 910434
- LWB 847400
- FMCBES-1375 801654
- FMCBES 1125 801696
- FMCBES 1125 801696
- FMBS-1625 801992
- OPS-1375 801695
- TCC-7 835197
- BTBA-10 927418
- STC940 927211
- STB940 927268
- XTB Guard 835449
- BTBA-12 927507
- TM340 912751
- TA110A 964412
- SC100 964420
- PC210 913071
- CSB125F 960768
- CSB 175 F 970259
- TB800 911542
- Air Volume Booster 964228
- EN50-85 964231
- EN40-1B 912028
- TCB07 835186
- XTB Cooling Enhancement 835175
- TCC Caliper 835121