Formax FD 260 User Manual
Page 39
35
CAUTION
PULLING MAIL PIECES IN THE OPPOSITE
DIRECTION THAT THEY MOVE THROUGH THE FD
260 MAY DAMAGE THE SWEEP OR MOVE IT OUT
OF POSITION.
3. If you cannot reach the jammed mail pieces,
continue through the following instructions.
4. Set the GAP ADJUSTMENT LEVER to thick, if it
is set for thin. (Refer to Figure 9.2.)
5. Push the FOAM ROLL ASSEMBLY toward the
end with the spring attached. Pull out the other
end, as you push in the spring end. Make sure the
other end clears the side frame. (Refer to Figure
9.2.)
6. Remove any mail pieces jammed at the feed rolls.
7. Push the spring-loaded end of the FOAM ROLL
ASSEMBLY in its hole in the non-operator side
panel. Place the other end of the FOAM ROLL
ASSEMBLY into the d-hole in the operator side
frame. (Refer to Figure 9.2.)
8. Set the GAP ADJUSTMENT LEVER to thin if you
are tabbing mail pieces thinner than
1
/
8
".
To remove mail pieces jammed between the belts
and metal rolls at the end of the FEED TRAY:
WARNING
DO NOT PLACE FINGERS OR TOOLS BETWEEN
OR NEAR MOVING PARTS.
1. Turn the POWER SWITCH off.
2. Pull the mail pieces from the feed tray. Make sure
all belts are centered on the metal rolls before you
resume tabbing.
- FD 1500 Plus
- FD 1500 Plus
- FD 1500 Plus
- FD 1500 Plus
- FD 1500 Plus
- FD 1202
- FD 1202
- FD 2030 Quick Setup Guide & Test Sheet
- FD 2030 Quick Setup Guide & Test Sheet
- FD 2030 Quick Setup Guide & Test Sheet
- FD 2030 Quick Setup Guide & Test Sheet
- FD 1502 Plus
- FD 2052 Operator Manual, 4th Edition
- FE 2032
- FD 2000IL System
- FD 2052 Quick Setup Guide & Test Sheet
- FD 2052IL System
- FD 382 / FD 38X
- FD 382 / FD 38X
- FD 2082
- FD 6100
- FD 2084
- 2200 Series
- FD 6102
- 6202 Series
- 6200 (600) Series
- 6302 Series
- 6304 Series
- 6402 Series
- 6600 Series
- 6206 Series
- 6204 Series
- 6900 Series
- 7100 Series
- 6606 Series
- 6404 Series
- FD 314
- FD 314
- FD 305
- FD 312
- FD 320
- FD 332
- 7102/7102XT Series
- 7200 Series
- FD 372
- FD 340
- FD 380
- FD 342
- FD 3200
- FD 120
- FD 125
- FD 4170
- FD 4400
- FD 540
- FD 670
- Cut-True 13M
- Cut-True 16M
- Cut-True 16M
- Cut-True 22S
- FD 210M
- Cut-True 27S
- FD 215S
- FD 230
- FD 260-10
- FD 260-20
- Cut-True 27A
- FD 280
- FD 280-10
- FD 130
- FD 452
- FD 280-20
- 402 Series
- 402 Series, Rev. 2
- FD 150
- FD 402A1 Operator Manual
- FD 402TA1
- FD 160
- FD 404A1 Operator / Parts Manual
- V-STACK36
- Roller Cleaning Kit Instructions
- FD 180
- FD 4060