GAI-Tronics VoIP Telephone Software Configuration Guide - Manual (Page 82)

GAI-TRONICS
VoIP Telephone Configuration Guide Page 82 of 88
CADENCE ON:OFF
This command sets the cadence for a contact output. To be on
for ON/10 seconds where ON is in tenths of seconds, and then
OFF for OFF/10 seconds. The default value for ON is 10, and
OFF is 0 implying the contact does not “flash”. Values in the
range 0-6000.
SHOW ALL
This command outputs the current settings of the Logic
Module

9.14 SIP Module Command Line Syntax
Action
Verb
Parameters Comment
1 2 3
SET
LOCALPORT XXXX
Configures the port number used for the local SIP
signalling socket to be XXXX. The default value is 5060.
RTPTOS XX
This command sets the value of the TOS/Diffserv field in
the UDP packets carrying RTP data. Valid values are 1-
>63 (Default value = 46)
REGTIMEOUT xxxxx
This command sets the Registration timeout value that
will be suggested by the telephone to a Registrar to be
XXXXX Seconds .
REREGTIMEOUT XXXXX
Sets a period in seconds after which the phone will force
a re-registration period and the server cannot override it.
PROXYFAILOVERST
ATUSES
XXX, XXX …
Contains a list of SIP status codes that will trigger a fail
over from one proxy to the next.
DONTSTARTMEDIAA
TRING
[ON | OFF]
Delay the sending of media packets to end points until
the call has been answered.
SENDDTMFLAST [ON | OFF]
Reorder the codec sequence to end points, so that the
DTMF codec is sent last.
SINGLEPTIME [0-63]
Forces a single packet time to the value set in ms. See
5.4.
SENDMULTIPARTMI
ME
[ON | OFF]
This option is for future enhancement and should always
be set to ‘OFF’. Default value OFF.
NEWBRANCHONAUT
HBYE
[ON | OFF]
This is a legacy option that is no longer used, and must
always be set to 'ON'. Default value 'ON'.
MODE
[SERIAL |
MULTIPLE]
Sets whether multiple proxies and registrars are used
serially or concurrently.
LOCALID [1-4] Identity
Sets the identity of the user/phone that will be used in the
registration process with a registrar.
DOMAIN [1-4]
FQDN minus
host name
Sets the domain name to be a FQDN without the leading
host part.
PROXY [1-4]
xxx.xxx.xxx.xx
x
or FQDN
Sets the IP address or the FQDN of the SIP proxy server
to be used for incoming/outgoing calls.
PROXYPORT [1-4] XXXX
The port number on the proxy used for SIP protocol
signalling can be changed to XXXX using this command.
The default value is 5060
PRIORITY [1-4] [1 – 4] Sets the failover sequence between the 4 proxies
REGISTRAR [1-4]
xxx.xxx.xxx.xx
x
or FQDN
This command sets the address of the Registrar to be
xxx.xxx.xxx.xxx or the FQDN specified. The registrar
address and the proxy may or may not be the same
address , but the address for registration must be set
here.
REGISTRARPORT [1-4] XXXX
Port number to send the requests to. Is 5060 by default
or if unspecified.
USERNAME [1-4] “username”
This command sets the username for the authorisation
realm to be username ( Default value is blank)
PASSWORD [1-4] “password”
This command sets the password for the authorisation
realm to be password ( Default value is blank)
ENDPOINT [1-4]
[ENABLED |
DISABLED]
Sets whether this set of proxy parameters is active.
SHOW ALL
3XE  D