Dimplex EBY15 User Manual

Page 4

Advertising

Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF

Remote Control Operation

Warning: It takes some time for the receiver to respond to the transmitter.
Do not press the buttons more than once within two seconds for
correct operation. On the control panel, switch B must be in the ‘ON’
position in order for the PCB to operate.

Setting

Operation

Flame effect

Press ‘I’ button once

Flame effect and heat

Press ‘I’ button again

By continuously pressing the ‘I’ button the fire will cycle between flame
effect and flame effect plus heat.
To turn off any of the settings press the ‘O’ button once.

The remote control may be placed, when not in use, in the wall-mounted
holster provided (see Fig. 10).

Thermal Safety Cut-out

For your safety, this appliance has been fitted with thermal cut-out. In
the event that the product overheats, the cut-out switches the appliance
off automatically.
To bring the appliance back into operation, remove the cause of the
overheating, then unplug or turn off the electrical supply to the heater
for up to 10 minutes.
When the heater has cooled sufficiently, re-connect and switch on the
heater.
Caution: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE ATTEMPTING ANY MAINTENANCE.

Lamp Replacement - see Fig.’s 7 & 8

There are two lamps located beneath the fuel effect. To gain access to
the lamps, remove the coal and place in a container. Remove the grate/
fuel effect by unscrewing the two screws, lift away the grate/fuel
effect to allow access to the bulbs - see Fig. 7.
Remove the defective lamp by unscrewing it as shown in Fig. 8.
Replace with a 60W E14 SES Clear Candle lamp. Take care not to over-
tighten the lamp.
Refit the fuel effect and replace the coal.

Cleaning

WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully with
a soft cloth. DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush attachment
of a vacuum cleaner should occasionally be used to clean the outlet
grille of the fan heater.

Recycling

For electrical products sold within the European
Community.
At the end of the electrical products useful life it should
not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice in your country.

After Sales Service

Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product
free of charge (excluding lamps & subject to availability) provided it
has been installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer
services help desk on 0845 600 5111. It would assist us if you can
quote the model number, series, date of purchase, and nature of the
fault at the time of your call. The customer services help desk will also
be able to advise you should you need to purchase any spares.
Please do not return a faulty product to us in the first instance as this
may result in loss or damage and delay in providing you with a
satisfactory service.
Please retain your receipt as proof of purchase.

UK customer help line 8.00am–5.00pm Mon-Fri and 8:30am-1.00pm Sat (October-March)

Customer Services:

Tel.

0845 600 5111

Fax.

01489 773053

e-mail [email protected]

Republic of Ireland

Tel.

01 8424833

Advertising