Maytag ADB1700ADB Dimension Guide User Manual

Undercounter dishwasher

Advertising
background image

PRODUCT DIMENSIONS

Undercounter Dishwasher

PRODUCT MODEL NUMBERS

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Page 1 of 2

Electrical Requirements: 120-volt, 60 Hz, AC-only, 15- or

20-amp. fused electrical supply. Copper wire only. A

time delay fuse or circuit breaker and separate circuit is

recommended.
If direct wiring dishwasher: Use flexible, armored or
nonmetallic, sheathed copper
wire with grounding wire that
meets the wiring requirements for
your home and local codes and ordinances.
Use a UL Listed or CSA Approved conduit connector.
If connecting dishwasher with a power supply cord:
Use power supply cord kit (Part
Number 4317824) marked for use
with dishwashers. Follow the kit
instructions for installing the power supply cord.
Power supply cord must plug into a grounded

three-prong outlet located in the cabinet next to

the dishwasher opening. Outlet must meet all local

codes and ordinances.
Water Supply Requirements: A hot water line with 20 to

120 psi (138 to 862 kPa) water pressure. Water

temperature must be 120°F (49°C) water at dishwasher.

Use " O.D. copper tubing with compression fitting or

flexible braided water supply line
Note: " minimum plastic tubing is not recommended.
Use a 90° elbow with " hose connection with rubber

washer (part number W10273460). Do not solder within 6"

(15.2 cm) from water inlet valve.
Drain Requirements: A new drain hose is supplied with

your dishwasher. If this is not long enough, use a new drain

hose with a maximum length of 12' (3.7 m) (Part No.

3385556) that meets all current AHAM/IAPMO test

standards, is resistant to heat and detergent, and fits the 1"

(2.5 cm) drain connector of the dishwasher.
Make sure to connect the drain hose to waste tee or

disposer inlet above drain trap in house plumbing and 20"

(50.8 cm) minimum above the floor. It is recommended

that the drain hose either be

looped up and securely

fastened to the underside of

the counter, or be connected

to an air gap.
Make sure to use an air gap

if the drain hose is

connected to house

plumbing lower than 20"

(50.8 cm) above subfloor or

floor.

Use " (1.3 cm) minimum I.D. drain line fittings.
If required, the air gap should be installed in accordance

with the air gap installation instructions. When connecting

the air gap a rubber hose (not provided) will be needed to

connect to the waste tee or disposer inlet.

air gap

C

B. For panel-ready models, dishwasher

depth is 24" (60 cm) not including the

" (1.9 cm) custom door panel.

C. Door handles may protrude forward

of the face of the dishwasher; varies

by model.

A. Insulation may be compressed

(not used on all models).

3 " - 4 "

(8.8 cm - 10.6 cm)

For 4" (10 cm) toe

kick, height of cabinet

opening is 34 " (86.3 cm).

24

"

(62.2 cm)

B

23

"

(60.6 cm)

"

(1.9 cm)

A

33

"

(85,1 cm)

min

. with

wheels

rem

oved

"

(9.4

cm)

21 "

(53.3 cm)

30"

(76.2 cm)

ADB1700AD

W10741197A

01/2015

Advertising
This manual is related to the following products: