Fig.4, Fig.3 – Sealey ML500X User Manual
Page 2
3. GENERAL INSTRUCTIONS
3. INTRODUCTION & SPECIFICATION
WARNING! Ensure the light is disconnected from the mains power supply before
attempting any of the following.
3.1.
TRIPOD LEGS
3.1.1
open tripod legs and lock in position by tightening the screw fixing. see fig.3A.
3.2.
TELESCOPIC STAND
3.2.1
to extend the upright support, loosen the locking collar at the end of each section, raise the inner
support to the required height and tighten the locking collars.
3.3.
LIGHT SOURCE
3.3.1
fit the light to the top of the stand. check that the electrical cable runs directly down the stand to
the floor.
DO NOT allow the cable to extend across the workshop above floor level. check that the
assembly is secure and that all nuts and bolts are tight (
DO NOT overtighten). stand light on a
suitable, level surface before use.
3.4.
BULB CHANGING
WARNING! Disconnect the light from the power supply and allow to cool before attempting
to touch the unit. DO NOT touch the new halogen bulb as the natural oil from your fingers
will shorten the bulb life. Handle with a dry, clean cloth only.
3.4.1. Loosen the screw on the top of the front cover (fig.4) and undo, allowing the front cover to open.
check to ensure that the screw is retained in the front cover tab (3) by the washer.
3.4.2. remove the old bulb and discard. Hold the new bulb (1) in a clean cloth and insert it (always use
the correctly rated bulb).
3.4.3. check that the weather seal is correctly located in the rim (4) and the washer is on the securing
screw. close the font cover. seal by tightening the securing screw.
3.5.
GENERAL
use only original sealey parts for repair or replacement. repairs must only be undertaken by a
qualified electrician. clean the light with a dry, dust-free cloth.
DO NOT use solvents or abrasives
to clean the light. Avoid touching the glass shield (fig.4.2) as handling may reduce service life
and cause the glass to crack. If necessary clean the shield (when cold) with alcohol and a soft
cloth. If the glass is damaged, replace it immediately. use genuine sealey replacement glass.
DO
NOT use other glass and DO NOT use the light without the glass shield.
DO NOT use the light without the front cover seal intact.
fig.4
DO NOT handle halogen bulbs as the natural oil from your fingers will shorten the bulb life. Handle only with a soft dry cloth.
DO NOT stand on the legs of a telescopic stand, and DO NOT hang other items, or tools, from a telescopic stand.
DO NOT use the light without the front glass shield. Avoid touching the glass shield as handling may reduce its serviceable life and cause the glass to crack.
DO NOT use the light without the weather seals intact.
DO NOT use the light near flammable, combustible or explosive liquids, solids, gases or equipment.
When not in use, switch off the light and disconnect from the power supply. Ensure that the unit is cool and dry and then store in a safe, dry, childproof area.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park
,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
Original Language Version
ML500X.V3 Issue no:1 - 25/06/10
fig.3
tungsten/Halogen tubes in die-cast alloy head. Heavy-duty lamp unit supported on telescopic pole with locking rings. Adjustable tripod base can be secured in
multiple positions, ideal for where access is limited and providing compact storage when not in use. fitted with 1.8mtr lead and Bs/AstA approved plug. supplied
with class c 400Watt halogen bulb.
POWER ....................400W
INPUT ....................... 230V
MAX/MIN HEIGHT ................ 0.96/1.8mtr
Replacement Bulb ............. ML400B