Exmark VH3615KA User Manual
Page 32
![background image](/manuals/83628/32/background.png)
- 27 -
b)
With blade drive engaged (lever pulled up, adjust the linkage length to
where the lower end of the bellcrank just clears the axle support gusset
(See Figure 9). Make sure the assist arm is against the rear assist arm
stop on the deck (See Figure 10). Push the lever down to the disengaged
position. The assist arm should contact the front assist arm stop on the
deck. If it does not contact, readjust so that the bellcrank is closer to the
gusset.
FIG. 9
BLADE ENGAGEMENT LINKAGE
5.2.4
Blade Safety Switch:
a)
Stop engine and remove spark plug wire(s).
b)
With blades disengaged and the bellcrank touching the rear of the slot in
the engine deck, adjust the blade safety switch mounting bracket (if
needed) until the bellcrank depresses the plunger by 1/4”.
c)
Be sure the bellcrank DOES NOT touch the switch body or damage to
the switch could occur.
d)
Retighten switch blade mounting bracket.
5.2.5
Engine to Cutter Deck Belt:
a)
Stop engine and remove spark plug wire(s).
b)
Check belt guides under rear engine and front mower deck to see that
they are properly set (See Section 5.2.6).
c)
Belt must be tight enough so it does not slip during heavy loads while
cutting grass. Over-tensioning will reduce belt and spindle bearing life. To
adjust belt tension, loosen the 5/16" whizlock nut on turnbuckle and
rotate the turn buckle; rotate turnbuckle toward rear of mower to tighten,
and toward front of mower to loosen belt tension (See Figure 10).
For 48” Decks: If there is no adjustment left in the turnbuckle and the
belt is still loose, the rear idler pulley can be repositioned in the front hole
(See Figure 10). The belt guide located next to the pulley must also be
repositioned in the front hole when the pulley is moved. The turnbuckle
will need to be readjusted.
Check belt tension after the first hour of operation and at least twice
during the first 24 hours of operation. Adjust as necessary.
Note: After readjusting the belt tension check the belt guide adjustment
Section 5.2.7
and blade brake adjustment Section 5.2.6.
- Lazer Z XS lXs29lKa725
- E-Series
- Pioneer S-Series Lawn Mower PNS20KA443
- Ultra VAC LAZER AS
- Ultra Vac 4500-420
- FMD604
- Quest Bagger 000 & higher
- Mhp3615ka
- Lazer ZCT
- Lazer ZXP
- METRO 21 MPKA21
- Commercial 21 4500-686 Rev. B
- Turf Tracer S-Series TTS18KA523
- lazer Z E-Series 0
- FontRunner FR27
- NAV27KC
- Metro 21
- Metro 26
- Navigator 4500-368
- LAZER Z D-SERIES Mower 0
- Quest Lawn Mower
- Turf Tracer TT23KCC
- Vantage VT691KA524CA
- Lazer Z 4500-485
- Frontrunner
- Lawn Tractor
- Pioneer S-Series 312
- Standon 4500-436
- Lawn mower COMMERCIAL 21
- TT4817KA
- Turf Tracer S-Series 312
- LAZER Z 4500-484
- Mhp4815kac
- Phazer PHZ19KA343CA
- OCD01
- Lazer Z CT
- Lazer Z Mower 4500-507
- Turf Tracer HP 4500-358
- Vikingtm Hydro 4500-355
- LAZER Z 4500-471
- Lazer Z Advantage Series X
- Frontrunner 4500-497
- lazer Z 000 & Higher
- Lazer Z HP 505
- Turf Tracer x-series LP FMD604
- NAVIGATOR 4500-367
- Mower Pioneer E-Series 4500-996 Rev A
- Lazer Z 4500-872
- LAZER ZTM
- Quest Bagger 4500-438 rev. a
- Metro 21 Series
- FR20KC
- Lazer Z SX Diesel Models 4500-501 Rev A
- LZ27KC604
- Viking VH15KA483 ECS 15
- Lazer Z HP 465
- Commercial 21 000 & higher
- Metro 4500-353
- Navigator 850
- M217bsp
- OCD02
- Lazer ZHP
- Quest 4500-451
- Lazer Z XS
- Ultra Vac QDS 850
- FrontRunner Air-Cooled
- VH15KA362
- Cd48cd
- Standon 4500-435
- Lazer Z Advantage Series
- Turf Tracer HP 4500-359
- Lazer Z Mower 4500-645
- 4500-371
- TT23KAEP
- Quest 4500-450
- NAV20KC
- Phazer 4500-461
- Ultra Vac Lazer Z AS
- Ultra Vac 4500-421
- FR604
- Self Propelled Mower
- Frontrunner 4500-341
- Phazer 820
- Lazer Z D-Series 000 & higher
- Turf Tracer HP 4500-540 Rev. B
- FMD524
- Turf Tracer 4500-528
- M216KASPC
- 4500-370
- FrontRunner Diesel
- TR23KC
- Lazer Z XP
- Lazer XS 4500-380
- Phazer
- Turf Tracer TT23KAE
- FR524
- M216KASP
- Quest Bagger
- Ultra Vac
- Lazer Z
- QUEST 4500-339
- LAZER Z 103-0656
- Advantage Series 4500-466
- FMD 604
- Pioneer S-Series 000 & Higher
- Lazer Z DS-Series LZDS
- Lazer HP
- Metro 4500-352
- Lazer Z Advantage Series Models 850
- Metro
- Metro 26 EN
- Lazer Z S-Series