Eaton POWERWARE 9315 User Manual

Eaton Tools

Advertising

Table of contents

Document Outline

Powerware 9315 UPS 500–750 kVA Installation and Operation Manual
Important Safety Instructions
Special Symbols
Table of Contents
List of Figures
Chapter 1 Introduction
- 1.1 UPS Features
- 1.2 Options and Accessories
- 1.3 Basic System Configurations
- 1.4 Safety Warnings
- 1.5 Conventions Used in This Manual
- 1.6 For More Information
- 1.7 Getting Help
Section I - Installation
Chapter 2 UPS Installation Plan and Unpacking
- 2.1 Creating an Installation Plan
- 2.2 Inspecting and Unpacking Each Cabinet
Chapter 3 Installing the UPS System
- 3.1 Preliminary Installation Information
- 3.2 Unloading the UPS Cabinets from the Pallet
- 3.3 Single Module Installation
  - 3.3.1 Installing UPS Internal Power and Control Wiring
  - 3.3.2 Installing UPS External Power and Control Wiring
- 3.4 Multi-Module Installation
  - 3.4.1 Installing UPS Internal Power and Control Wiring
  - 3.4.2 Installing UPS External Power and Control Wiring
- 3.5 Installing Input/Rectifier Customer Connections
- 3.6 Installing Output/Inverter Customer Connections
- 3.7 Installing Accessories
- 3.8 Initial Startup
- 3.9 Completing the Installation Checklist
- Installation Checklist
- Notes
Chapter 4 Installing a Remote Battery Disconnect
Chapter 5 Installing a Remote Emergency Power-off Control
Chapter 6 Installing Optional Accessories
- 6.1 Installing an RMP
- 6.2 Installing an RIM
- 6.3 Installing an SCM
- 6.4 Installing X-Slot Cards
Section II - Operation
Chapter 7 Understanding UPS Operation
- 7.1 Operating Modes
Chapter 8 Using the Control Panel
- 8.1 Using the LCD Screen
- 8.2 Using the Pushbuttons
- 8.3 Adjusting the Contrast
- 8.4 Reading the Status Indicators
- 8.5 Using the Menu Options
Chapter 9 UPS Operating Instructions
- 9.1 UPS Controls and Indicators
9.2 Starting the UPS
9.3 Starting the UPS in Bypass Mode
9.4 Transferring to Bypass Mode
9.5 Transferring to Normal Mode
9.6 Transferring to Bypass and Shutting Down the UPS
9.7 Shutting Down the UPS and Critical Load
9.8 Using the UPS Emergency UPM Off Pushbutton
- 9.8.1 Using the UPS Emergency UPM Off Pushbutton
- 9.8.2 Resetting the UPS System after an Emergency UPM Off
Chapter 10 Using Features and Options
- 10.1 Building Alarm Monitoring
- 10.2 General Purpose Relay Contacts
- 10.3 Optional Remote Monitor Panel
- 10.4 Optional Relay Interface Module
- 10.5 Optional Supervisory Contact Module
Chapter 11 Responding to System Events
- 11.1 System Event Horns
- 11.2 System Event Indicators
- 11.3 System Event Messages
Chapter 12 Communication
- 12.1 Locating the Customer Interface Panel
- 12.2 Connecting Equipment to a Serial Port
- 12.3 Configuring the Serial Ports
- 12.4 Terminal Mode
- 12.5 System Configuration Mode
- 12.6 Calibration Mode
- 12.7 Computer Mode
- 12.8 Remote Monitor Mode
- 12.9 eNotify Service
  - 12.9.1 eNotify Service Features
  - 12.9.2 Installing eNotify Service
- 12.10 Remote Notification
- 12.11 X-Slot Cards
Chapter 13 Maintaining the UPS System
- 13.1 Important Safety Instructions
- 13.2 Performing Preventive Maintenance
Chapter 14 Product Specifications
- 14.1 Model Numbers
- 14.2 UPS System Input
- 14.3 UPS System Output
- 14.4 Environmental Specifications
Chapter 15 Warranty
Appendix A Installation Reference
- A.1 Physical Features and Requirements
- A.2 UPS System Oneline Configurations
- A.3 Power Wiring Installation Notes
- A.4 Location of UPS Terminals
- A.5 Customer Interface Wiring Notes
- A.6 Typical REPO
- A.7 RMP Dimensions and Mounting Details
- A.8 RIM Dimensions and Mounting Details
- A.9 SCM Dimensions and Mounting Details
- A.10 Battery Disconnect Switch Dimensions