Home Automation OMNI-BUS 125A00-1 - Manual

© 2010 Home Automation, Inc. www.homeauto.com Document: 125I00-1, Rev1.0 May 2010
HAI Omni-Bus 6-Channel Keyfob Remote Control
Model 125A00-1
User’s Guide
SPECIFICATIONS
o 6 Channels
o For use with HAI Omni-Bus Output devices
o Requires an HAI Omni-Bus RF Transceiver on an Omni-Bus
network
o Frequency: 433.92MHz
o Range: Up to 30m (indoors), up to 100m (outdoors)
REMOTE CONTROL FUNCTIONS
To switch a device ON or OFF
Press and release the button on the
Remote Control. The remote control
will toggle between the ON and OFF
commands each time the button is
pressed.
To DIM a light (when used with an Omni-Bus Dimmer unit)
Enter DIM/BRIGHT mode on the Remote control by pressing
buttons 1 and 2 simultaneously.
Press and hold the appropriate
button on the Remote Control to dim
or brighten the light.
The Remote Control will exit the DIM/BRIGHT mode automatically
if no buttons are pressed for 7 seconds.
A forced exit can be achieved by pressing buttons 1 and 2
simultaneously again.
OMNIBUS PROGRAMMING
See the HAI OMNIBUS Software User Guide for more information
on how to program the remote control into an Omni-Bus output
devices using the OMNIBUS Installation Software.
MANUAL PROGRAMMING
1. Place the receiving device into the programming mode. This is
normally done by pressing and holding the button on the
receiving device until its LED starts flashing continuously.
(See receiving device user guide for more information).
2.
Press and hold the DESIRED
channel button on the Remote
Control until the remote sounds 3
beeps (approx.10 seconds). Check
for a confirmation signal from the
receiving device. (See receiving
device user manual for more
information).
3. Exit the programming mode on the receiving device.
REMOTE CONTROL BATTERY REPLACEMENT
If the remote control does not respond to any key presses or the
LED fails to come on when a key is held in, the battery may need
replacement.
The remote control uses one type 23A 12V battery.
DELETING A REMOTE CONTROL
A Remote Control channel programmed into an Omni-Bus receiving
device may be deleted from that device via the OMNIBUS Installation
Software or by following the procedure below:
1. Place the receiving device into the programming mode. This is
normally done by pressing and holding the button on the
receiving device until the receiving device LED starts flashing
continuously (see receiving device user guide).
2.
Press and hold the appropriate button
on the remote control until the remote
sounds 3 beeps followed by another
set of 4 beeps. Check for a
confirmation signal from the receiving
device. (See receiving device user
manual for more information).
3. Exit the programming mode on the receiving device.
DELETE ALL
All remote control channels programmed into ANY Omni-Bus
RECEIVING device can be deleted entirely by using any Omni-Bus
Remote Control. The remote control used for this does not
necessarily need to be one that was previously programmed into the
device. This allows a lost or stolen remote control to be deleted
before reprogramming the new remote control.
1. Place the receiving device into the programming mode. This is
normally done by pressing and holding the button on the
receiving device until the receiving device LED starts flashing
continuously (see receiving device user guide).
2.
Press and hold any button on the
remote control until the remote sounds
3 beeps, then 4 beeps and then 5
beeps (approximately 17 seconds).
Check for a confirmation signal from
the receiving device. (See receiving
device user manual for more
information).
3. Exit the programming mode on the receiving device.
KEYPAD LOCK FUNCTION
The keypad lock function can be used to prevent accidental remote
control activation.
Enabling the Keypad Lock Function
Before the keypad lock function can be used, it has to be enabled as
follows: Press and hold button 3 and 4 simultaneously until the
remote sounds a burst of beeps (after approximately 5 seconds).
Disabling the Keypad Lock Function
Press and hold button 3 and 4 simultaneously until the remote
sounds a short beep (after approximately 5 seconds).
Locking/Unlocking the Keypad
Lock or Unlock the Keypad on the Remote Control by pressing
buttons 3 and 4 simultaneously. The Remote Control will sound a
long beep when the Keypad is locked and any key is pressed on the
remote control.
®