Sorting tv channels automatically (follow tv), Automatic tuning – Polycom VIDEOPLUS VR630/07 User Manual
Page 10
10
EN
Sorting TV channels automatically
(Follow TV)
When the automatic channel search function is
activated, the TV channels are saved in a specific
order. This may vary from the order of TV chan-
nels on the TV.
This function changes the order of TV channels
saved in the video recorder to match that of the
TV.
Make sure that the video recorder and the TV
are connected by a scart cable.
1.
1.
Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.
Press
. The main menu will appear.
3.
3.
Select 'TUNER SET UP' with
and
confirm with
.
4.
4.
Select 'FOLLOW TV' with
and
confirm with
.
5.
5.
'P:01' will appear in the video recorder dis-
play.
6.
6.
Select programme number '1' on the TV.
7.
7.
Confirm with
on the video recorder
remote control. The video recorder compares
the TV channels on the TV and the video
recorder.
If the video recorder finds the same TV chan-
nel as on the TV, then it stores it at 'P01'.
8.
8.
Wait until the next number, e.g. 'P:02' appears
in the display.
9.
9.
Select the next programme number on the
TV, e.g. '2'.
10.
10.
Confirm with
.
11.
11.
Repeat steps 8 to 10 until you have assigned
a programme number to all TV channels.
12.
12.
To end, press
.
Automatic Tuning
During installation, all available TV channels are
searched for and saved. If the channel assign-
ments of your cable or satellite TV provider
change or if you are re-installing the video
recorder, e.g. after moving house, you can start
this procedure again. This will replace the TV
channels already saved with the new ones.
1.
1.
Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.
Press
. The main menu will appear.
3.
3.
Select 'TUNER SET UP' with
and
confirm with
.
4.
4.
Select 'AUTO TUNING' with
and
confirm with
.
5.
5.
The automatic TV channel search starts. This
allows the video recorder to save all available
TV channels. This procedure may take sever-
al minutes.
6.
6.
When the TV channel search is complete,
'COMPLETED' will briefly appear on the TV
screen.
B 1
L C
K B
B 1
L C
K B
MENU
STATUS/EXIT
B 1
B 1
B 1
L C
K B
B 1
L C
K B
MENU
SELECT K L CHOOSE B
AUTO TUNING
MANUAL TUNING
→FOLLOW TV
MOVE
END=EXIT
I cannot switch my TV set to programme
number '1'
* If you have connected additional devices to
socket AV2(DECODER), please disconnect
these devices. Because of other connected
devices, the TV set could switch to the pro-
gramme number of the scart socket.
'NO TV SIGNAL' will appear in the TV screen.
The video recorder is not receiving a video
signal from the TV.
Check the plug on the scart cable.
Check your TV's operating instructions to see
which scart socket is used for video signals.
If this does not help, it's not possible to use this
function. Please read the section 'Sorting TV
channels manually'.
What does Easy Link do ?
With Easylink, TV channels are always trans-
fered from the TV to the VCR. A new TV chan-
nel must be tuned on the TV set. The transfer is
then done automatically to the VCR.
PLEASE WAIT
START
FINISH
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚
VR630/07 02.2.6 10:13 AM Page 10