Dexter Laundry T-30 (On-Premise) - Manual (Page 17)

- 17 -
5) Press and release the SELECT/ENTER touch pad switch on the dryer controller. Once the
SELECT/ENTER touch pad switch is pressed and released, the dry time L.E.D. will switch off, the dry cycle
L.E.D. and programming L.E.D. will remain on, the temperature L.E.D. will illuminate, and the drying
temperature will be shown on the 4-digit numeric display.
6) Press and release either the UP or DOWN touch pad switch on the dryer controller to change the drying
temperature. Each press and release of either the UP or DOWN touch pad switch will either increase or
decrease, respectively, the temperature by five degrees Fahrenheit or three degrees Celsius, depending on how
your dryer controller is set up. Once either the UP or DOWN touch pad switch is pressed, the temperature
L.E.D. and the drying temperature on the 4-digit numeric display will flash. If you press and hold down either
the UP or DOWN touch pad switch, you will increment (UP arrow) or decrement (DOWN arrow) your way
through the available drying temperatures (105° Fahrenheit or 41° Celsius, up to 195° Fahrenheit or 90°
Celsius). If you do not want to change the drying temperature, do not press either the UP or DOWN touch
pad switch. Go to the next step
7) Press and release the SELECT/ENTER touch pad switch on the dryer controller. Once the SELECT/ENTER
touch pad switch is pressed and released, the temperature L.E.D. will switch off, the dry cycle L.E.D. and
programming L.E.D. will remain on, the cool down L.E.D. will illuminate, and the cool down time will be shown
on the 4-digit numeric display.
8) Press and release either the UP or DOWN touch pad switch on the dryer controller to change the cool down
time. Once either the UP or DOWN touch pad switch is pressed, the temperature L.E.D. and the cool down
time on the 4-digit numeric display will flash. If you press and hold down either the UP or DOWN touch pad
switch, you will increment (UP arrow) or decrement (DOWN arrow) through the cool down times available
(2 through 60 minutes if the controller has a red dot sticker or 2 through 15 minutes if the controller has no
red dot sticker). To not change the cool down time, do not press either the UP or DOWN touch pad
switch. Go to the next step.
9) Press and release the SELECT/ENTER touch pad switch on the dryer controller. Once the SELECT/ENTER
touch pad switch is pressed and released, the cool down L.E.D. and the programming L.E.D. will switch off,
the dry cycle L.E.D. will remain on, and the flashing cool down time on the 4-digit display will stop flashing
and remain.
10) At this point, you have two choices:
a) You can perform the modified dry cycle by pressing and releasing the START touch pad switch on the
dryer controller touch pad. If you start the modified cycle, the total dry time will appear on the 4-digit
numeric display and it will count down to 0 as the dry cycle progresses.
b) You can clear the modified dry cycle program by pressing and releasing the STOP touch pad switch. If
you choose to clear the modified dry cycle, the 4-digit numeric display will change to “LOAd”.
TEMPORARY DRYER CONTROLLER PROGRAMMING EXAMPLE
REQUIREMENTS: Dry a load with 40 minutes of actual heat at 185°F and five minutes of cool down.
The following procedure will show you how to temporarily modify the existing dry cycle 1 program for one cycle of
drying. It is based on the assumption that the factory defaults have not been permanently changed. If they have
been changed, the steps of this procedure will be the same, but the values that are displayed will be different. The
amount of times that the UP or DOWN touch pad switches of the dryer controller must be pressed and released
may also be different.
If you want the change to be permanent, go to the “PERMANENT DRYER CONTROLLER PROGRAMMING”
section of this manual.
PROCEDURE:
1) After the load has been placed in the dryer, press and release the UP or DOWN touch pad switch on the
dryer controller until the L.E.D. for dry cycle 1 is illuminated.
2) Press and release the CYCLE touch pad switch on the dryer controller. You will see the number “35” on the
dryer controller display. The programming L.E.D. and dry time L.E.D. will be illuminated.