Dexter Laundry T-30 (On-Premise) - Manual (Page 19)

- 19 -
cycle L.E.D. and the programming L.E.D. will remain illuminated, and the total dry time will also be
displayed on the 4-digit numeric display.
6) Press and release either the UP or DOWN touch pad switch on the dryer controller to change the total dry
time. Once either UP or DOWN touch pad switch is pressed, the dry time L.E.D. and the total dry time on
the 4-digit numeric display will flash. If you press and hold down either the UP or DOWN touch pad switch,
you will increment (UP arrow) or decrement (DOWN arrow) through the total dry times available (1 through
60 minutes). The dry time on the controller display includes the cool down time along with the heated
time. To not change the total dry time, do not press either the UP or DOWN touch pad switch. Go to the
next step.
7) Press and release the SELECT/ENTER touch pad switch of the dryer controller. Once the
SELECT/ENTER touch pad switch is pressed and released, the dry time L.E.D. will switch off, the dry
cycle L.E.D. and programming L.E.D. will remain on, the temperature L.E.D. will illuminate, and the drying
temperature will be shown on the 4-digit numeric display.
8) Press and release either the UP or DOWN touch pad switch of the dryer controller to change the drying
temperature. Each press and release of either the UP or DOWN touch pad switch will either increase or
decrease, respectively, the temperature by five degrees Fahrenheit or three degrees Celsius, depending on
how your dryer controller is set up. Once either the UP or DOWN touch pad switch is pressed, the
temperature L.E.D. and the drying temperature on the 4-digit numeric display will flash. If you press and hold
down either the UP or DOWN touch pad switch, you will increment (UP arrow) or decrement (DOWN
arrow) your way through the available drying temperatures (105° Fahrenheit or 41° Celsius, up to 195°
Fahrenheit or 90° Celsius). If you do not want to change the drying temperature, do not press either the
UP or DOWN touch pad switch. Go to the next step.
9) Press and release the SELECT/ENTER touch pad switch on the dryer controller. Once the
SELECT/ENTER touch pad switch is pressed and released, the temperature L.E.D. will switch off, the dry
cycle L.E.D. and programming L.E.D. will remain on, the cool down L.E.D. will illuminate, and the cool down
time will be shown on the 4-digit numeric display.
10) Press and release either the UP or DOWN touch pad switch on the dryer controller to change the cool down
time. Once either the UP or DOWN touch pad switch is pressed, the cool down L.E.D. and the cool down
time on the 4-digit numeric display will flash. If you press and hold down either the UP or DOWN touch pad
switch, you will increment (UP arrow) or decrement (DOWN arrow) through the cool down times available
(2 through 60 minutes if the controller has a red dot sticker or 2 through 15 minutes if the controller has no
red dot sticker). To not change the cool down time, do not press either the UP or DOWN touch pad
switch. Go to the next step.
11) Press and release the SELECT/ENTER touch pad switch on the dryer controller. Once the SELECT/ENTER
touch pad switch is pressed and released, the cool down L.E.D. will switch off, the dry cycle L.E.D. and
programming L.E.D. will remain on, and the 4-digit numeric display will change to “Prog”.
12) Press and release the STOP touch pad switch on the dryer controller to save the cycle program and escape
the programming mode. If you want to change the same dry cycle program again, press the
SELECT/ENTER touch pad switch and continue at step 6 of this procedure. If you want to modify another
dry cycle program, go to step 4 of this procedure and continue.
13) If you pressed the STOP touch pad switch to escape the programming mode, you may now start the dry
cycle by pressing the START touch pad switch.
PERMANENT DRYER CONTROLLER PROGRAMMING EXAMPLE
REQUIREMENTS: Dry a load with 50 minutes of actual heat at 195°F and three minutes of cool down.
The following procedure will show you how to permanently modify the existing dry cycle 1 program for one
cycle of drying. It is based on the assumption that the factory defaults have not been permanently change. If
they have been changed, the steps of this procedure will be the same, but the values that are displayed will be
different. The amount of times that either the UP or DOWN touch pad switch of the dryer controller must be
pressed and released may also be different.
If you want the change to be temporary (for only one dry cycle), go to the “TEMPORARY DRYER CONTROLLER
PROGRAMMING” section of this manual.