Asus A8N-SLI Premium - Manual (Page 54)

2 - 2 8 2 - 2 8 2 - 2 8 2 - 2 8 2 - 2 8 C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
1 1 . 1 1 . 1 1 . 1 1 . 1 1 . Chassis intrusion connector (4-1 pin CHASSIS) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )
This connector is for a chassis-mounted intrusion detection sensor or
switch. Connect one end of the chassis intrusion sensor or switch
cable to this connector. The chassis intrusion sensor or switch sends a
high-level signal to this connector when a chassis component is
removed or replaced. The signal is then generated as a chassis
intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. Remove the jumper caps only when you intend to
use the chassis intrusion detection feature.
Never connect a U S B c a b l e U S B c a b l e U S B c a b l e U S B c a b l e U S B c a b l e to the IEEE 1394 connectors. Doing so will
damage the motherboard!
1 2 . 1 2 . 1 2 . 1 2 . 1 2 . IEEE 1394 connector (10-1 pin IE1394_2) I E E E 1 3 9 4 c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 2 ) I E E E 1 3 9 4 c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 2 ) I E E E 1 3 9 4 c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 2 ) I E E E 1 3 9 4 c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 2 )
This connector is for the IEEE 1394a module. Connect the IEEE 1394
module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
A8N-SLI PREMIUM
®
A8N-SLI PREMIUM Chassis intrusion connector
CHASSIS
+5VSB_MB Chassis Signal GND
(Default)
A8N-SLI PREMIUM
®
A8N-SLI PREMIUM IEEE 1394 connector
IE_1394_2
1
GND +12V
TPB1-
GND
TP
A1-
+12V TPB1+ GND TP
A1+