HP StorageWorks Scalable File Share - Manual (Page 26)

## Template ADD network --bootproto static --device %{prep_ext_nic} \
--ip %{prep _ext_ip} --netmask %{prep_ext_net} --gateway %{prep_ext_gw} \
--hostname %{host_name}.%{prep_ext_search} --nameserver %{prep_ext_dns}
%{prep_ext_nic} must be replaced by the Ethernet interface name. eth1 is recommended for
the external interface and eth0 for the internal interface.
%{prep_ext_ip} must be replaced by the interface IP address.
%{prep_ext_net} must be replaced by the interface netmask.
%{prep_ext_gw} must be replaced by the interface gateway IP address.
%{host_name} must be replaced by the desired host name.
%{prep_ext_search} must be replaced by the domain name.
%{prep_ext_dns} must be replaced by the DNS name server IP address or Fully Qualified
Domain Name (FQDN).
IMPORTANT: The InfiniBand IPoIB interface ib0 cannot be set up using this method, and must
be manually set up using the procedures “Configuration Instructions” (page 30) .
In all the following lines, %{ks_harddrive} must be replaced by the installation device, usually
cciss/c0d0 for a DL380 G5 server. The %{ks_ignoredisk} should list all other disk devices on
the system so they will be ignored during Kickstart. For a DL380 G5 server, this variable should
identify all other disk devices detected such as
cciss/c0d1,cciss/c0d2,sda,sdb,sdc,sdd,sde,sdf,sdg,sdh,... For example:
## Template ADD bootloader --location=mbr --driveorder=%{ks_harddrive}
## Template ADD ignoredisk --drives=%{ks_ignoredisk}
## Template ADD clearpart --drives=%{ks_harddrive} --initlabel
## Template ADD part /boot --fstype ext3 --size=150 --ondisk=%{ks_harddrive}
## Template ADD part / --fstype ext3 --size=27991 --ondisk=%{ks_harddrive}
## Template ADD part pv.100000 --size=0 --grow --ondisk=%{ks_harddrive}
These Kickstart files are set up for a mirrored system disk. If your system does not support this,
you must adjust the disk partitioning accordingly.
The following optional, but recommended lines set up the name server and ntp server.
## Template ADD echo "search %{domain_name}" >/etc/resolv.conf
## Template ADD echo "nameserver %{nameserver_path}" >>/etc/resolv.conf
## Template ADD ntpdate %{ntp_server}
## Template ADD echo "server %{ntp_server}" >>/etc/ntp.conf
%{domain_name} should be replaced with the system domain name.
%{nameserver_path} should be replaced with the DNS nameserver address or FQDN.
%{ntp_server} should be replaced with the ntp server address or FQDN.
3.3 Installation Phase 1
3.3.1 DVD/NFS Kickstart Procedure
The recommended software installation method is to install CentOS 5.2 and the HP SFS G3.1-0
software using the DVD copies of both. The installation process begins by inserting the CentOS
5.2 DVD into the DVD drive of the DL380 G5 server and powering on the server. At the boot
prompt, you must type the following on one command line, inserting your own specific
networking information for the node to be installed and the NFS location of the modified Kickstart
file:
boot: linux ks=nfs:install_server_network_address:/install_server_nfs_path/sfsg3DVD.cfg
ksdevice=eth1 ip=filesystem_server_network_address netmask=local_netmask gateway=local_gateway
Where the network addresses, netmask, and paths are specific to your configuration.
During the Kickstart post-installation phase, you are prompted to install the HP SFS G3.1-0 DVD
into the DVD drive:
26 Installing and Configuring HP SFS Software on Server Nodes