Cabela's Commercial Food Dehydrator 28-0301 - Manual (Page 8)

-8- -13-
PROGRAMMING
7. TO SET THE TIME: Press the “TIME” Button on the Control Panel one time.
Use the “UP” & “DOWN” Buttons on the right side of the Control Panel to set
the countdown timer hours (23 hour maximum). Press the “TIME” Button again to
switch to minutes. Similarly set the minutes (5 minute increments).
8. TO SET THE TEMPERATURE: Press the “TEMP” Button one time. Use the
“UP” & “DOWN” Buttons to set the temperature (160 o F maximum, 50 o F minimum,
5 degree increments).
NOTE: Set Temperature is the maximum temperature the Dehydrator could reach
during operation.
9. You do not need to push any other buttons. The Dehydrator will automatically
start after a brief pause. NOTE: The Dehydrator will start while you’re programming
if you delay. Don’t worry, this is normal. Just continue programming as instructed
above.
...PROCEED TO “FUNCTION”
FUNCTION
10. The Digital Display on the Control Panel will continuously cycle while the unit
is operating. It will alternately display: the preset drying time “SET TIME;” the
remaining drying time “TIME REMAINING;” the preset temperature “SET TEMP;”
and the actual current temperature inside the Dehydrator “ACTUAL TEMP”
(measured by the Temperature Sensor on the back wall near the top).
NOTE: The “SET TEMP” is only the highest temperature reached during a heating
cycle. The “SET TEMP” is NOT maintained.
11. The Dehydrator will emit 8 beeps at startup and when the interior temperature
reaches the preset value.
12. The Dehydrator automatically stops (Fan & Heater) when the countdown timer
reaches 0. Unit power will remain on, however.
...PROCEED TO “POST OPERATION”
Digital Display
WHEN DRYING...
LIGHT BULB REPLACEMENT
1. Turn off the Dehydrator Lights. Turn off and disconnect the Dehydrator from the
power outlet.
2. Let the
Dehydrator cool. DO NOT attempt to replace a Light Bulb while the
Dehydrator is hot.
3. Remove all of the
Racks.
4. Remove the Back Panel of the Dehydrator.
5. Locate the LED Light Fixture that you wish to
replace, and disconnect the wires from the Light
Fixture from the white Wire Connector on the unit
by squeezing together the two clips on the Wire
Connector.
6. Press together the two sides of the
Metal Clip on
the Light Fixture to release it from the body of the
Dehydrator and then gently push the Light Fixture
into the Cabinet of the unit, being sure to have a grip
on the wires connected to the Light Fixture so it does
not drop into the Dehydrator Cabinet. Discard the removed Light Fixture.
7. Insert the replacement Light Fixture into the vacant hole where the old Light
Fixture was by first feeding the wire connected to the Light Fixture first.
8. Line up the
Light Fixture with the hole and push it back until the Metal Clips on the
back of the Light Fixture lock into place.
9. Re-connect the Wire Connector attached to the Light Fixture with the Wire Connector
the old Light Fixture was connected to by pressing them together until they lock.
10. Line the Back Panel of the Dehydrator up and re-install the removed screws to
mount the Back Panel.
WARNING! Before cleaning, assembling or disassembling the
Dehydrator, make sure the Dehydrator is OFF and the PLUG IS REMOVED
FROM THE OUTLET/POWER SOURCE!
SAUSAGE OR SNACK
STICKS: Use the Snack
Stick Hangers to hang
and dry sausage links and
snack sticks. After removing
all the Racks from your
Dehydrator, simply drape
the links over the Snack
Stick Hangers and slide
them into the top Rack
Supports. Be sure not to
allow the links to rest on the bottom of the Cabinet or on top of the Diffuser.
GROUND MEATS: Whenever making jerky from ground meats, you can use a
jerky gun or such tool to create perfect strips of jerky as well as snack sticks.
Snack Stick
Hangers
Rack Supports
Rack Supports
LED Light
Fixture
Wire
Connector
Wire
Connector
Push
Metal
Clip
Push
Metal
Clip
LED Light
Fixture