Diamondback Fitness 660Tm - Manual (Page 18)

18
6 0 0 S E R I E S T R E A D M I L L O W N E R’ S M A N U A L
Maintenance
Always inspect hardware prior to any exercise session. Turn power
switch to the “OFF” position and unplug electrical cord from the
outlet before attempting maintenance. Inspect unit for loose parts
and frayed wires. Repair or replace any damaged or worn parts,
tighten all loose hardware as necessary.
After training, always wipe down your 650T/660T unit. Perspiration
that continuously settles on frame, pads or casing may eventually
cause rust or damage to the unit. Damage resulting from lack of
proper maintenance will not be covered under warranty.
A proper maintenance will extend the life and ensure a better perfor-
mance of the treadmill. Below you will find our recommendations
for the maintenance of your 650T/660T:
Overall Cleaning
Use a damp cloth to clean outer surface and console of the tread-
mill. DO NOT USE PETROLEUM BASED PRODUCTS TO CLEAN
ANY PART OF THE TREADMILL . Use a clean, lint free, cloth to
occasionally clean the deck surface.
Belt/Deck Maintenance
Lubrication to the deck is very important to your 650T/660T. It will
reduce the wear of the deck and maintain the smooth running sur-
face. Although this treadmill has been pre-lubed at the factory but
periodic lubrication is still necessary. It is difficult to predict exactly
when the belt will need lubrication, one of the most common symp-
toms is a hesitation or pause of the belt when you set your foot.
Here are some of the tips for deck lubrication:
• Wipe entire deck surface with a clean, lint free cloth.
• Lubricate deck with the Diamondback Lubrication Kit (which can
be purchased through your Diamondback Dealer under Diamond-
back Part No. 84-19-000
• Follow the instructions as specified in the Lubrication Kit.
• Lubricate your 650T/660T treadmill approximately every 6
months of normal use .
Belt Adjustment
Proper belt adjustment is important for smooth and safe operation
of the treadmill. If the belt is too loose, you will feel a slight hesita-
tion each time you take a step. (If this symptom occurs, first turn the
treadmill off and try lubricating the deck/belt – see Belt/Deck Main-
tenance.)
The adjustment screws must be tightened evenly in order to adjust
the belt properly. The adjustment screws are located at the rear of
the treadmill in the end caps.
Both adjustment screws should be tightened 1/4 turn in a clockwise
direction with a wrench and the belt checked for slipping after each
adjustment. If the belt continues to slip, repeat this process until the
belt stops slipping. Make sure to only turn the adjustment screws
1/4 turn each time until the slipping stops. This will insure that you
do not over-tighten the rollers. Over-tighten the rollers may cause
serious damage to the treadmill.
If the belt tracks too close to one side, loosen the adjustment screw
on the opposite side, turning it counterclockwise 1/4 turn. Restart
the treadmill and run it at 5 mph / 8 kph for 1 to 2 minutes to insure
the belt will stay in the center. Repeat the procedure if necessary.
Error Code
This console has a self-detected program. It will detect an error and
report on the console screen. If any of such error occurs, contact
your authorized Diamondback fitness dealer.
Error 1 - Speed sensor error
Error 2 - Over speed error
Error 3 - Safety key · Re-ensure the safety key is engaged.
Error 5 - Elevation motor error
Error 11 - Communication error
Noise
If noises develop or malfunctions occur, contact your authorized
Diamondback fitness dealer.
Treadmill will not start
1. Not plugged in ➡ Re-plug the power cord of this treadmill
2. Safety key not engaged ➡ Ensure the safety key is engaged
3. Power switch at “OFF” position ➡ Make sure the treadmill power
switch is at “ON” position
4. Treadmill circuit breaker tripped ➡ Reset or replace fuse
If there is power going into the treadmill and the treadmill is still not
starting, contact your authorized Diamondback fitness dealer.
Trouble Shooting Guide