Learn name macro use page – Marantz SR8002 User Manual

Page 23

Advertising
background image

ENGLISH

20

Erasing All

This procedure clears (resets) all programmed
codes and names. Once all the data is cleared, the
memory is returned to the factory default status. The
programmed macros are also erased.

1 3

4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

LEARN

NAME

MACRO

USE

PAGE

1

2 3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

1.

Hold down the M button for three seconds or

more.

The menu is displayed.

2.

Press

the

D5 (ERASE) direct button .

The

USE

and

LEARN

indicators blink.

3.

Press

the

CLEAR button while holding down

the POWER ON and OFF buttons at the same
time.

4.

Press

the

D4 (YES) direct button to erase.

All programmed codes and names are erased and

reset to the factory default settings.

• To cancel the erasing operation, press the

D5 (NO) button to return to the previous
screen.

• To erase all operation takes a few seconds

after the D4 (YES) button is pressed.

PROGRAMMING MACROS

This remote controller can program a series of button
operations in sequence.
Macros are a function that makes it possible to
use a single button operation to perform a complex
series of button operations any number of times. A
single button can be programmed to perform up to
20 steps in sequence. A total of 20 buttons can be
programmed with macros.

• For example, the following sequence of operations

can be programmed to a macro.

Switch

amplifi er to DVD source → Set amplifi er

mode to AUTO → Play DVD player → Switch TV
to video input

The factory default for the transmission interval
(time) between macro operations is one second,
but these signal transmission intervals can be set
between approximately 0.5 seconds and 5 seconds
in the Setup mode. Each transmission interval can
be adjusted independently when programming or
revising a macro.

Note:

• If the signal transmission interval (interval time)

is changed using the Setup mode (described later),
this transmission interval is applied to all macro
programs. To change individual signal transmission
intervals, use the procedures in this section for
programming macros and revising macros.

• No signals are transmitted while programming a

macro.

• The M button, > button, cursor buttons, MEMO

button, CLEAR button, and VOL buttons cannot
be programmed.

• If no button is pressed for approximately one

minute during programming, the remote controller
returns to the state before macro mode.

In this case, the macro program is not stored.

• When executing macro mode, performing the

source switching operation two or more times
only changes the remote control mode and does
not transmit any signals. (Switching of the source
selector of the amplifi er is valid only once.)

PROGRAMMING MACROS

This example shows how to program a macro to the
M-01 button.
(The screens shown in the example are the default
factory states. If the names of direct buttons
were rewritten, these modified names would be
displayed.)
Switch amplifi er to DVD source → Play DVD player
→ Set the interval to 2 seconds until the next signal is
sent → Switch TV to video input → Set the amplifi er
mode to AUTO

1 2 3

LEARN

NAME

MACRO

USE

PAGE

1

2 3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

1.

Hold down the M button for three seconds or

more.

The menu is displayed.

2.

Press

the

D4 (MACRO) direct button .

The macro menu is displayed.

The

MACRO

indicator displays and

LEARN

blinks.

3.

Press

the

D1 (M-01) direct button .

The menu has four pages, and so use the > button

to select the page when programming other buttons.

4.

Press the buttons in the sequence that you

want the operations performed.

The actual program starts here.

Each time a button is pressed, the name of the

button is displayed on the LCD.

4-1 4-2 4-3

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

4

-1

.

Press the DVD source button .

4

-2

.

Press the

2 (PLAY) button .

4

-3

.

Press the

3 or 4 cursor buttons .

The interval time is displayed on the LCD.

4

-4

.

Press the

3 or 4 cursor buttons and set to 2.0

(seconds).

• Use

the

3 cursor button to increase the time

and the

4 button to decrease the time. The

interval time can be set from 0.5 seconds to
5 seconds.

• To stop the time adjustment, press the D5

(CANCEL) direct button.

4

-5

.

Press the OK cursor button .

4

-6

.

Press the TV source button .

4

-7

.

Press the > button to display the fi rst page.

4

-8

.

Press the D1 (INPUT) direct button .

4

-9

.

Press the AMP source button .

4

-10

.

Press the > button to display the fi rst page.

4

-11

.

Press the D1 (AUTO) direct button .

4

-12

.

Press the OK cursor button .

The LCD displays END to indicate that programming
is completed.

5.

To program another macro, repeat the

procedure in steps 3 to 4-12.

6.

To exit macro programming, press the M button

.

The

USE

indicator displays to indicate that the

remote controller can now be operated.

When the macro are programmed 20 operations or

more, the display returns macro menu.

Edit the macro so that it has 20 operations or less.

EXECUTING MACRO PROGRAMS

1 2 3

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

1.

Press

the

M button shortly.

The macro menu is displayed.

2.

Press

the

D1 (M-01) direct button .

3.

Check that the operations of the program are

executed step by step.

The name of the operation button is displayed on

the LCD.

• The programmed section is indicated by

&. The bar indicator moves to indicate the
progress of the program.

Select

DVD

source

→ PLAY transmit → Interval

time: 2 seconds → Select TV → TV INPUT transmit
→ Select AMP → AUTO transmit → End

• To cancel transmission of the program while

it is in progress, press any button.

CHANGING NAMES OF MACRO PROGRAMS

Under the factory default settings, the names of the
macro programs are set from M-01 to M-20, but you
can change them to any desired name.
The text can have up to six characters, and it is
entered using the numeric buttons.
This example shows how to change the M-01 name
to MOVIE.

1 2 3

LEARN

NAME

MACRO

USE

PAGE

1

2 3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

4 5 6

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

LEARN

NAME

MACRO

USE

PAGE

1 2

3 4

1.

Hold down the M button for three seconds or

more.

The menu is displayed.

Advertising
This manual is related to the following products: