Marantz SR8002 - Manual (Page 68)

65
ENGLISH
DOLBY HEADPHONE MODE
This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the MENU button
automatically switches to the Dolby headphone
mode.
The OSD that appears when the MENU button is
pressed is shown below.
H E A D P H O N E
D O L B Y H P M O D E : D H
S U R R O U N D : P L II M V
L L E V E L : + 1 0 . 0 d B
R L E V E L : 0 . 0 d B
DOLBY HP (Headphone) MODE can be selected
with the left and right cursor buttons.
BYPASS → DH (DOLBY Headphone) → BYPASS
BYPASS: Bypasses the Dolby headphone mode
and delivers ordinary 2-channel stereo.
DH: Dolby Headphone is a signal processing
system that delivers a sound similar to
room speakers.
It makes it possible to experience the
volume and space of a 5-channel
surround system using ordinary stereo
headphones.
When the PURE DIRECT mode is selected, Dolby
surround processing is bypassed and “
✽✽✽” is
displayed as the mode indication.
The surround mode can be selected when the
modes in DH is selected.
L/R LEVEL can be set in the ±12 dB range.
Notes:
• The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
• In headphone mode, Tone Control and ACOUSTIC
EQ are not available.
ATTENUATION TO ANALOG INPUT SIGNAL
2 3 1
5 6 4
8
0
9 7
MEMO CLEAR
PREV MUTE
MENU EXIT
GUIDE
TEST CH.SEL
LIP.SYNC
SURR
7.1CH ATT SPK-AB
DISP OSD
THX
SLEEP
5
ATT
If the selected analog audio input signal is greater
than the capable level of internal processing, the
“PEAK” indicator will light up on the front display. If
this happens, you should press the ATT button on
the remote controller.
“ATT” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD/CD-R, VCR1-OUT and
DSS/VCR2-OUT.
This function is memorized for each individual input
source.
SPEAKER A/B
DIGITAL VIDEO S-VIDEO AUX 1 INPUT
VOLUME
DOWN
M-DAX ENTER MENU
7.1CH INPUT
MULTI
A/B
T-MODE MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
SPEAKER MULTI
L C R SL S SR LFE DIGITAL SURROUND V-OFF ULTI AUTO TUNED ST SPKR A B NIGHT PEAK ANALOG DIGITAL ATT SURR DIRECT AUTO DISC 6.1 MT X 6.1 EQ PCM AAC
2 3 1
5 6 4
8
0
9 7
MEMO CLEAR
PREV MUTE
MENU EXIT
GUIDE
TEST CH.SEL
LIP.SYNC
SURR
7.1CH ATT SPK-AB
DISP OSD
THX
SLEEP
6 SPK-AB
This unit has speaker system - A and speaker
system- B for front L/R channels.
You can select these systems by pressing
SPEAKERS A/B button on the front panel or SPK-
AB on the remote controller.
7.1 CH INPUT
This unit is equipped for future expansion through the
use of Multi channel Super Audio CD multichannel
player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video
sources
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR8002
E MENU
PURE DIRECT THX
7.1CH INPUT
MODE AUTO MULTI
PURE DIRECT
SURROUND SPEAKER MULTI
DSD
POWER ON/OFF
DISP MULTI AUTO TUNED ST SPKR A SLEEP SURR DIRECT AUTO DISC 6.1
1. 2.
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO
VOLUME
UP DOWN
M-DAX A/B
DE MEMORY CLEAR
SPEAKERS
MIC
L C R SL S SR LFE DIGITAL SURROUND
M
4.
2 3 1
5 6 4
8
0
9 7
MEMO CLEAR
OK
VOL CH
PREV MUTE
MENU EXIT
GUIDE
TEST CH.SEL
LIP.SYNC
SURR
7.1CH ATT SPK-AB
DISP OSD
THX
SLEEP
4
7.1CH
2.
4.
3.
4.
2
CH.SEL
1. Select a desired Video source to decide the
routed video signal to the Monitor Outputs.
2. Press the 7.1 CH INPUT button on the front
panel or press 7.1 CH on the remote controller
to switch the 7.1 channel input.
3. If it is necessary to adjust the output level of
each channel, press the CH.SEL button on the
remote controller.
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –12 to +12 dB.
The subwoofer can be adjusted between –18
and +12 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
4. Adjust the main volume with the MAIN
VOLUME knob or the VOL buttons on the
remote controller.
To cancel the 7.1 CH. INPUT setting, press the 7.1
CH INPUT button on the front panel or press 7.1 CH
on the remote controller.
Notes:
• When the 7.1 CH. Input is in use, you may not select
a surround mode, as the external decoder determines
processing.
• In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.
• Furthermore, the following functions are not
available during 7.1 CH Input use.
Test Tone, NIGHT MODE, Source Direct, Pure
Direct, RE-EQ, Tone Control, Multi EQ