Troy-Bilt 2-Cycle Trimmer TB32 EC User Manual

Tb32 ec, Operator’s manual, Need help

Advertising
background image

IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.

Removing Unit From Carton

Place shield onto mount
bracket
. Securely screw 2 shield
screws
through holes on mount
bracket and into shield. Make
sure screws are tightened equally
so there is an equal gap between
bracket and shield on each side.

Assemble The Unit

1

1

2

Remove all contents from
the carton.

Starter Rope

Fuel Cap

Throttle Control

On/ Off Switch

D-Handle

Ez-Link™

Cutting Head Shield

Need Help?

Call 1-800-828-5500

Electric Starter or

Power Start Bit Optional!

THESE OPTIONAL ACCESSORIES

ARE SOLD SEPARATELY!

This unit has an alternate starting method
that many find easier to use than pulling a
rope. Please contact a local retailer or call

1-800-828-5500 for more information.

Information may also be found at

www.troybilt.com

DIDN’T START?

Repeat these instructions.

IF engine fails to start after 2 attempts,

move choke lever to position 3 and pull

the starter rope until engine starts

IF unit still fails to start, refer to the

operator’s manual for additional starting

and troubleshooting information

Assembly Tools
Required:
Phillips #2 Screwdriver

Assemble The Unit

Starting The Unit

Remove cap from lower
boom. Push cutting
attachment into coupler.
Turn coupler knob clockwise
to tighten.

Mix thoroughly in separate
fuel can:
– 3.2 fl. oz. of 2-cycle

engine oil

– 1 gallon of unleaded

gasoline

NOTE: Do not mix directly in

fuel tank.

Place unit on a level surface.
Fill fuel tank.

Press primer bulb 10 times,
or until fuel is visible

Crouch in starting position.

SQUEEZE and HOLD
throttle for ALL further
steps.

Pull rope 5 times.

Move choke lever to
Position 2 and squeeze
throttle.

Pull rope 3-5 times to start
engine. Run unit for 30-60
seconds
to warm up.

Continue to squeeze
throttle.
Move choke lever
to Position 3.

1

1

2

Remove all contents from
carton.

5

6

7

1

9

10

3

Put D-handle on shaft. Move
handle a minimum 6 inches
away from shaft grip. Insert
clamp bolt and tighten the
wing nut.

Move choke lever to
Position 1.

Continue to squeeze
throttle.
Run unit for an
additional 60 seconds to
complete warm-up. Unit
may be used during this
time.

8

4

Starting The Unit

11

12

13

14

15

Primer

Bulb

10 X

5 X

3-5 X

Choke Lever

1 Gallon

3.2 oz

40:1

Choke Lever

Choke Lever

Min. 6"

Bump
Knob

Inner

Reel

Outer
Spool

Spring

Top Hole

Bottom Hole

Split Wall

Unscrew the bump knob
counterclockwise.

Remove the inner reel and
spring.

Cut one 6-foot (1.8 m) length
of new 0.095” split line
trimming line. Split each end
about 6 inches (150 mm).

Insert the end of one line into
the top hole and the end of
the other line into the bottom
hole.

Wind the line tightly in the
direction shown on the inner
reel. The split wall will divide
the line. Wind the line until it
is completely divided and
about 6 inches (150 mm) of
line remains.

Insert the two 6-inch sections
into the two .095 holding
slots.

1

1

2

Pass the two line ends
through the eyelets. Place the
spring inside the inner reel.
Insert the inner reel into the
outer spool. Push the inner
reel and outer spool together.

Reloading the Line*

3

4

5

6

7

Hold the inner reel and outer
spool together. Firmly pull the
two line ends to release them
from the holding slots. Screw
the bump knob on clockwise.
Tighten the bump knob
securely.

1

8

For replacement line, call 1–800-828-5500 or go to
an authorized service dealer.

For single line installation or replacement spool
installation instructions, refer to the Replacing the
Trimming Line
section of this manual.

*This is to assist in the reloading of Splitline® only. These instructions
are NOT part of the fast assembly instructions. Line does not need to
be installed on the initial assembly and start-up.

Reloading the Line

Holding Slots

Eyelets

769-07375 P01

11/11

E

n

g

li

s

h

P

a

g

e

1

E

s

p

a

ñ

o

l

P

a

g

e

6

NEED HELP?

CALL 1-800-828-5500 IN U.S. OR 1–800–668–1238 IN CANADA

TB32 EC

2-Cycle Trimmer

Operator’s Manual

Advertising