TANDBERG Maestro MXP User Manual
User manual
Advertising
Table of contents
Document Outline
- 1 Introduction
- 2 Installation
- 3 General Use
- 3.1 The Welcome Screen
- 3.2 Using the Remote Control
- 3.3 On-screen Indicators
- 3.4 Using the Menu
- 3.5 Make a Call
- 3.6 Answer an incoming call
- 3.7 End Call
- 3.8 Standby
- 3.9 Phone Book
- 3.10 Camera Control
- 3.11 Presentation
- 3.12 Services
- 3.12.1 Request Floor and Release Floor
- 3.12.2 Conference Layout
- 3.12.3 Terminal Names
- 3.12.4 Chair Control
- 3.12.5 Assign Floor and Release Floor from Participant
- 3.12.6 View Site and End View
- 3.12.7 Disconnect Participant
- 3.12.8 Terminate Meeting
- 3.12.9 More about MultiSite (embedded MCU)
- 3.12.10 Text Chat
- 4 Control Panel
- 5 System Settings
- 5.1 General Settings
- 5.2 Menu Settings
- 5.3 Presentation Settings
- 5.4 Call Quality
- 5.5 Audio
- 5.6 Video
- 5.7 Security
- 5.8 Network
- 6 Peripheral Equipment
- Interfaces
- 6.2 Document Camera
- 6.3 DVD / VCR
- 6.4 Additional Cameras
- 6.5 Additional Microphones
- 6.6 The TANDBERG DNAM and Speakers
- TANDBERG 6000 MXP Profile, TANDBERG 6000 MXP, TANDBERG 7000 MXP, TANDBERG 8000 MXP and TANDBERG Maestro
- The DNAM audio system is built on two specially designed and separate modules; the DNAM audio amplifier and the DNAM loudspeaker cabinet. The DNAM loudspeaker cabinet is based on several editions, one for each of the 6000 MXP, 6000 MXP Profile, 7000 MXP and 8000 MXP systems. For the 6000 MXP and the 8000 MXP system, the audio amplifier is integrated in the loudspeaker cabinet. For the Maestro system the amplifier and the loudspeaker cabinet is integrated directly into the system pedestal.
- Using the external and optional Stereo Speaker Kit will improve the stereo sound, even on systems with integrated stereo speakers**. Note that the kit is not available for Mini-DNAM described below. Before connecting the Stereo Speaker Kit, make sure the complete videoconferencing system is powered down. When connecting the Stereo Speaker Kit to a system with already integrated stereo speakers, these integrated speakers will be disabled, and a new filter and specification setup is loaded when powering up the videoconferencing system.
- TANDBERG 6000 MXP Profile, TANDBERG 6000 MXP, TANDBERG 7000 MXP, TANDBERG 8000 MXP and TANDBERG Maestro
- 6.7 Stereo Speaker Kit
- 6.8 Telephone Add-On
- 6.9 Dual Monitor
- 6.10 XGA Monitors and Projectors
- 6.11 VESA Display Power Management
- 6.12 Digital Monitor Power Management
- 6.13 Extended Display Identification Data (EDID)
- 7 Appendices
- Appendix 1: Technical Specifications
- Appendix 2: Bandwidth Information for TANDBERG Endpoints
- Appendix 3: Environmental Considerations
- Appendix 4: Guidelines for Settings up Rooms for Video Meetings
- Appendix 5: Security
- Appendix 6: Using the File System
- Appendix 7: Web Interface
- Appendix 8: Connecting the System to PRI/T1
- Appendix 9: Connecting the System to Switched 56 Network
- Appendix 10: Connecting the System to ISDN using NT1 Network Adapters
- Appendix 11: TANDBERG Cameras
- Appendix 12: Remote Control (TRC3 / TRC4)
- Appendix 13: Cisco Call Manager Registration
- Appendix 14: Diagnostic Tools for IP
- Appendix 15: System Upgrade
- Appendix 16: Declaration of Conformity
- Appendix 17: Dimensions
- Appendix 18: Protocols Supported
- Appendix 19: Cable Specifications
- 8 Glossary
- 9 Index