Speaker setting, Advanced operations, Changing settings – Yamaha DVD-S1200 User Manual
Page 27
27
Advanced operations
B
A
LS
RS
L
R
SW
c
b
a
C
SETUP
SELECT
ENTER
RETURN
ms
ms
dB
0
dB
dB
L
Exit
Test
LS
R
SW
C
RS
dB
0
0
0
0
0
LS
LS
A
A
C
A
B
A
C
B
A
(L)
C
(L)
C
(R)
A
(R)
1
2
3
4
5
6
7
8
9
0
S
10
CANCEL
OPEN/CLOSE
POWER
MARKER
PAGE
GROUP
ENTER
VIDEO OFF
PLAY MODE SUBTITLE
AUDIO
ANGLE
TOP MENU
MENU
ON SCREEN
RETURN
SET UP
Í
/ I
AUDIO/VIDEO
Changing settings
Speaker setting
[DVD-A] [DVD-V]
Select either “2-channel” or “Multi-channel” to suit the speakers you
have connected. You can change the following settings when you
select “Multi-channel”.
»
A
Speaker presence and size
1. Use the cursor buttons [
3
,
4
,
2
,
1
] to select the item and
press [ENTER].
2. Press the cursor buttons [
3
,
4
] to select the setting and
press [ENTER].
Icon examples: Rear speaker (L)
Large: When the speaker supports low-frequency (under
100 Hz) reproduction.
Small: Select when the speaker does not support low-frequency
reproduction.
The size setting for the main speakers is automatically determined by
the setting for the subwoofer.
»
B
Delay time
[DVD-V]
(Dolby Digital, center and rear speakers only)
For optimum listening with 5.1-channel sound, all the speakers, ex-
cept for the subwoofer, should be the same distance from the seating
position. If you have to place the center or rear speakers closer to the
seating position, adjust the delay time to make up for the difference.
If distance
=
(from the center speaker) and
?
(from the rear speak-
ers) are the same as or greater than
>
(from the main speakers),
leave the delay time as “0”, the factory preset.
If either distance
=
or
?
is less than
>
, find the difference in the
relevant table and change to the recommended setting.
Changing the delay time
1. Use the cursor buttons [
3
,
4
,
2
,
1
] to select the delay time
box and press [ENTER].
2. Press the cursor buttons [
3
,
4
] to adjust the delay time and
press [ENTER].
»
C
Speaker balance
1. Use the cursor buttons [
3
,
4
,
2
,
1
] to select “Test” and
press [ENTER].
A test signal is output from one speaker at a time, starting with the
main left speaker and proceeding clockwise.
MAIN (L)
-)
CENTER
--)
MAIN (R)
e
v
REAR (L)
(----------------==
REAR (R)
2. While listening to the test signal, press the cursor buttons
[
3
,
4
] to adjust the volume of the center and rear speakers
so they are the same apparent volume as the main speakers
(
s
6 dB to
r
6 dB).
(The main speakers cannot be adjusted here.)
3. Press [ENTER].
The test signal stops.
Note
³
Test signal is effective only when you made analog connection.
When you make digital connection, make adjustment using the test
tone on the amplifier.
³
No signal is output for the subwoofer. To adjust its volume, play
something, then return to this screen to adjust to suit your taste.
When you are finished
Use the cursor buttons [
3
,
4
,
2
,
1
] to select “Exit” and press
[ENTER].
Note
The unit may be unable to output as set here due to limitations im-
posed by the unit itself or the disc being played. (The FL display’s
“P.PCM” indicator lights or “D.MIX” indicator goes out in these
cases.)
Difference
Approx. 50 cm
Approx. 100 cm
Approx. 150 cm
Approx. 200 cm
Setting
1.3 ms
2.6 ms
3.9 ms
5.3 ms
Center speaker
Difference
Approx. 200 cm
Approx. 400 cm
Approx. 600 cm
Setting
5.3 ms
10.6 ms
15.9 ms
Rear speakers
Rear
Test
signal
No
Large
Small
Exit
Cursor buttons/
ENTER
Subwoofer
Center
Main (L)
Main (R)