LockeyUSA M210 EZDC User Manual

Lockey m-210 deadbolt installation instructions, For m210 ez instructions, turn to reverse side

Advertising
background image

Step 5: Adjust Deadbolt (if necessary) & Install

1. Adjustable Deadbolt (#12) is preset to 2 3/8”.

To adjust, lift pin and slide to 2 3/4”.

2. With arrow pointed UP, insert Deadbolt

and secure with two (2) Wood Screws (#11).

No.

Part Name

M210

M210 EZ

1

Outside Body

1

1

2

Inside Body

1

1

3

Rubber Trim Plate

2

0

4

Mortised Strike

1

1

5

Spindle 40-55 mm.

1

1

6

Spindle 30-45mm.

1

1

7

Machine Screw M4 x 50 mm.

2

2

8

Machine Screw M4 x 35 mm.

2

2

9

Wood Screw M4

4

4

10 Extra Code Tumblers (Red)

1

1

11 Extra Non-Code Tumblers (Blue)

2

2

12 Adjustable Deadbolt 2 3/8” – 2 3/4”

1

1

13 Tweezers

1

1

14 Hex Bolts

2

0

15 Brass Support Pin

1

1

16 EZ-Plates-M210 EZ (Not Shown)

0

1

Door Edge

Step 7: Install the Lockey M210

5. Place the Rubber Trim Plate (#3) on the

backside of the Outside Body (#1).

6. Place the Outside Body

on the door. The hexagonal
bolts (#14) should extend
into the top and bottom holes.

7. The Support Pin (#15) on the Inside

Body should fit into and extend through
the hole in the Deadbolt (#12).
INSTRUCTIONS CONTINUED ON REVERSE SIDE

Step 6: Verify Correct Spindle Length

1. With deadbolt (#12) installed, hold

the Inside Body (#2) and Rubber Trim
Plate (#3) to the door.

2. Place Spindle (#5/6) through Deadbolt,

into the Inside Body, as far as possible.

3. Spindle should extend from exterior of door

3/8” min. – 5/8” max.

4. If the 30-45 mm (#6) is too long, cut it to the correct length.

IMPORTANT: If spindle extends less than 3/8” it may not engage the lock. If spindle
extends more than 5/8”, it will cause the lock to bind.

Step 4: Install Support Pin & Hex Bolts

Install Brass Support Pin (#15) into either hole
on Inside Body as shown in the figure to
the Right [Left].

Install/screw Hex Bolts (#14) into the top
and bottom of the Outside Body
as shown in the figure (Far Right).

Step 3: Identify Door Handing

Right-Hand Doors – From exterior of
door, hinges are on right-side. (Fig. 1)

Left-Hand Doors – From exterior of
door, hinges are on left-side. (Fig. 2)

The M210 is factory pre-handed for
right-hand doors. To change handing, remove two
blue screws and cover plate from Outside Body.

Now, move the pin from the right side of the
outside body to the hole on the left side. Replace
plate and screws.
*M210 DC – Inside Body handing pin must be
placed on opposite side from Outside Body.

Lockey M-210 Deadbolt
Installation Instructions

Step 2: Prep Door for Installation with Template

1. Place template (supplied) on door and fold along door’s edge.
2. Mark holes for 2 3/8” or 2 3/4” backset.
3. Drill holes as instructed.
NOTE: For Pre-Prepped 2 1/8” doors, you only need to drill top hole.

Inside Body (#2)

Spindle (#5/6)

3/8” to 5/8”

Step 1: Change User Code (OPTIONAL)

If you wish to change your code, see instructions on reverse side.

FOR M210 EZ Instructions, turn to reverse side.

Thumb-Turn

M210 | M210 EZ | M210 DC | M210 EZ DC

Inside Body

Outside Body

Adj. Pin

2 3/8”

2 3/4”

Advertising
This manual is related to the following products: