Brocade Virtual ADX Installation and Deployment Guide (Supporting ADX v03.1.00) - Manual (Page 76)

Virtual ADX-A(config-vlan-999)#untag eth 3
added untagged port ethe 3 to port-vlan 999.
Virtual ADX-A(config-vlan-999)#server backup eth 3 000c.292a.095c vlan 999 shared-
mac
Make sure the virtual switch is configured in promiscuous mode.
Reload required. Please write memory and then reload or power cycle.
Virtual ADX-A(config-vlan-999)#
Configuring SLB on the Standby Brocade Virtual ADX
Virtual ADX-B#config term
Virtual ADX-B(config)#vlan 100
Virtual ADX-B(config-vlan-100)#untag eth 1
added untagged port ethe 1 to port-vlan 100.
Virtual ADX-B(config-vlan-100)#exit
Virtual ADX-B(config)#ip address 192.168.1.13 255.255.255.0
Virtual ADX-B(config)#server real rs1 192.168.1.10
Virtual ADX-B(config-rs-rs1)#port http
Virtual ADX-B(config-rs-rs1)#exit
Virtual ADX-B(config)#server real rs2 192.168.1.11
Virtual ADX-B(config-rs-rs2)#port http
Virtual ADX-B(config-rs-rs2)#server virtual v1 192.168.1.12
Virtual ADX-B(config-vs-v1)#port http
Virtual ADX-B(config-vs-v1)#bind http rs1 http rs2 http
If the vSwitch is in the non-promiscuous mode, execute the following.
Virtual ADX-B(config-vs-v1)#vlan 999
Virtual ADX-B(config-vlan-999)#untag eth 3
added untagged port ethe 3 to port-vlan 999.
Virtual ADX-B(config-vlan-999)#server backup eth 3 000c.292a.095c vlan 999
Make sure the virtual switch is configured in non-promiscuous mode.
Reload required. Please write memory and then reload or power cycle.
Virtual ADX-B(config-vlan-999)#
If the vSwitch is in the promiscuous mode, execute the following.
Virtual ADX-B(config-vs-v1)#vlan 999
Virtual ADX-B(config-vlan-999)#untag eth 3
added untagged port ethe 3 to port-vlan 999.
Virtual ADX-B(config-vlan-999)#server backup eth 3 000c.292a.095c vlan 999 shared-
mac
Make sure the virtual switch is configured in promiscuous mode.
Reload required. Please write memory and then reload or power cycle.
Virtual ADX-B(config-vlan-999)#
Global Server Load Balancing
Global Server Load Balancing (GSLB) is a common deployment topology used to manage traffic
across one or more datacenters or sites. These sites are often distributed geographically. In this
release of the Brocade Virtual ADX, a Brocade GSLB controller configured on an ADX device can now
recognize a Brocade Virtual ADX instance as participating in a GSLB site, further increasing the
availability of the entire application across datacenters. The GSLB controller can communicate with
the Brocade Virtual ADX site as well as other ADX sites at the same time.
NOTE
The Brocade Virtual ADX currently supports GSLB site-specific functionalities only. RTT is not
supported in this release. For steps to configure GSLB Controller and site, refer to the ServerIron ADX
Global Server Load Balancing Guide
Configuring SLB on the Standby Brocade Virtual ADX
76 Brocade Virtual ADX Installation and Deployment Guide
53-1003241-01