American Dryer Corp. SL50 User Manual
American Dryer Corp. Dryers
![background image](/manuals/36770/1/background.png)
SL20 / SL31 / SL50 / SL75
Installation/Operator Manual
WARNING: For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion and to prevent property
damage, personal injury or death.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your
building.
•
Clear the room, building or area of all
occupants.
•
Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
•
If you cannot reach your gas supplier,
call the fire department.
— Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette
notice pour réduire au minimum le risque
d’incendie ou d’explosion ou pour éviter
tout dommage matériel, toute blessure ou
la mort.
— Ne pas entreposer ni utiliser d’essence
ni d’autres vapeurs ou liquides
inflammables à proximité de cet
appareil ou de tout autre appareil.
— QUE FAIRE SI VOUS SENTEZ UNE
ODEUR DE GAZ:
•
Ne pas tenter d’allumer d’appareils.
•
Ne touchez à aucun interrupteur. Ne
pas vous servir des téléphones se
trouvant dans le bâtiment.
•
Évacuez la pièce, le bâtiment ou la
zone.
•
Appelez immédiatement votre
fournisseur de gaz depuis un voisin.
Suivez les instructions du fournisseur.
•
Si vous ne pouvez rejoindre le
fournisseur de gaz, appelez le service
des incendies.
— L’installation et l’entretien doivent être
assurés par un installateur ou un service
d’entretien qualifié ou par le fournisseur
de gaz.
ADC Part No. 113403 - 14
American Dryer Corporation
88 Currant Road
Fall River MA 02720-4781 USA
Telephone: +1 (508) 678-9000 / Fax: +1 (508) 678-9447
e-mail: [email protected]
www.amdry.com
Document Outline
- Safety Precautions
- SL20 Specifications
- SL31 Specifications
- SL50 Specifications
- SL75 Specifications
- Installation Procedures
- Location Requirements
- Unpacking/Setting Up
- Dryer Enclosure Requirements
- Fresh Air Supply Requirements
- Exhaust Requirements
- Electrical Information
- Gas Information
- Converting from One Family of Gas to Another
- Gas Pressure Testing
- Steam Information
- Water Information
- Preparation for Operation/Start-Up
- Preoperational Test
- Preoperational Instructions
- Shutdown Instructions
- Service/Parts Information
- Service
- Parts
- Warranty Information
- Returning Warranty Cards
- Warranty
- Returning Warranty Parts
- Routine Maintenance
- Data Label Information
- SL2929
- AD-15 Phase 7
- ML-75DIII
- AD-236
- AD-50V
- ML-96HS
- 75 lb
- SL2020
- AD-758DV
- Aquatex AD-76
- MDG-75
- MLG-130DR (HSI)
- MLG31PCB
- AD-410
- AD-75THS
- Direct Spark Ignition ADG-530DSi II
- MLG32PD3
- ML-55
- ML-96
- ADG-410
- ADG-320D
- Phase 7 Gas/Steam AD-464
- AD-120ES
- Gas/Electric/Steam ML-55HS
- AD-840
- MDG31
- D20
- Aquatex AD-52
- Phase 7 D30
- 30 lb. Stacked Models
- 30 lb. Stacked Models
- 30 lb. Stacked Models
- ADH-120
- ML-96D
- Super AD-50
- ML-122
- SL31
- Super AD-30
- MDG30V
- AD-670
- SL31AD-15
- ADS-464 II
- ML-190
- Heat Reclaimer AD-170HR
- 50 lb. Single Pocket MDG50V
- 24 VAC Phase 5 AD-330
- D75
- ML-82 III
- /T75
- ML-75HS
- ML-75
- Phase 7 Gas/Steam ML-460
- ADG / MLG-170DR
- ADG-230
- CG20
- AD-385
- AD-385
- AD-385
- AD-400
- AD-400
- AD-400
- ADH-75
- EURO-24
- AD-230
- Phase 7 OPL with S.A.F.E. Gas DSI AD-78 IV
- MDG50PNH
- Phase 6 Microprocessor Controls ML-190HS
- MLG-96
- AD-27
- D3030
- AD-530HS
- AD-540
- AD-81 II
- ML-175
- ML-55II
- MDG75V
- SL20
- AD-360X2
- M31SL
- Phase 5 Microprocessor AD-170
- ADG-758
- ADG-30DS
- ML-78
- WDA-530D II
- Phase 7 OPL/Fire Suppression System EURO-14
- AD-235
- Phase 7 D90
- ML-145
- AD-75D II
- HBG76
- Extended Side Panels AD-120ES III
- MD-170
- AD/ML-310
- ML-310
- MDG75PNH
- ADG-531HS
- AD-310 Phase 7
- ML-758
- Hot Surface Ignition System ADG-530
- Dyer AD-26
- D-78
- AD-235D
- AD-81 III
- MLG33
- AD-115ES
- Phase 7 / OPL ensor Activated Fire Extinguishing System D120
- Gas HSI - Phase 7/FSS AD-78 III
- 24 VAC Phase 5 AD-320
- AD-24 II
- EURO-12
- ML-175DR
- Extended Side Panel AD-120ES II
- ML-170
- AD-75
- AD-20
- MLG32PDB
- Phase 6 Microprocessor AD-145
- Gas/HSI & Steam ID-120
- ML-130 II
- ML-75V
- HOT SURFACE IGNITOR GAS SL31-31
- HB76
- AD-30V
- ML-75DII
- Gas DSI/Electric/ Steam AD-78 II
- AD-758
- AD-115ES II
- WDA-385
- AD-758V
- MD-170PTVW
- ML-130DR
- AD-115
- Gas-HSI ADG-78 II
- 20/31
- T20
- ML-95
- MDG30PCC
- AD-75V
- ML-78III
- ADG-385
- EURO-35
- Gas DSI/HSI/Electric/Steam/Phase 7 with S.A.F.E. D-40
- ML-122D
- MLG-460
- UD-80
- AD-24 Phase 7
- ADS-464
- AD-60
- Wet Wash ML-79
- Phase 7.4.2 DMC None
- MLS-460
- AD-100
- AD-100
- AD-100
- ML-130 III
- Hot Surface Ignition ADG-530HS
- M50SL
- AD-4545
- MDG-50
- MDG-30
- Gas/Electric/Steam AD-75HS
- MLG31PCA
- AD-25V
- SL3131
- ML-78II
- ADG-464
- ID-170
- D170
- AD-310 Phase 7 Tilting