Electrolux EXM18HV1WE - Manual (Page 7)

7
Remote Control
tips and information
• When changing batteries, do not use old or
varied ones, otherwise, it may cause problems
with the remote control.
• If the remote control is not used for a long time,
remove the batteries as old batteries may leak
or corrode and damage the remote control.
• The battery life during normal use is about six
months.
• If the remote control does not operate normally,
please remove and refit the batteries. If
abnormal operation continues, replace with new
batteries.
8m
• The air conditioner will not operate if curtains,
doors or other materials block the signals from
the remote control to the indoor unit.
• Prevent any liquid from falling into the remote
control. Do not expose the remote control to
direct sunlight or heat.
• If the infrared signal receiver on the indoor
unit is exposed to direct sunlight, the air
conditioner may not function properly. Use
curtains to prevent the sunlight from falling on
the receiver.
• If other electrical appliances react to the
remote control, either move these appliances
or consult your local dealer.
Indoor Unit Display
• Keep the remote control where its signal can reach
the receiver of the indoor unit (a maximum distance
of 8m is allowed).
• When you select the timer operation, the remote
control automatically transmits a signal to the
indoor unit at the specified time.
• If you keep the remote control in a position that
hinders proper signal transmission, a time lag of up
to 15 minutes may occur.
• When the remote control sends out a signal, the
symbol will blink for about 1 second on the
display. The indoor unit will acknowledge the signal
with a beep when it receives an effective signal.
Heating Mode indicator
It lights when the heating function is activated
Cooling Mode indicator
It lights when the cooling function is activated
Power ON/OFF indicator
It lights when the appliance is running or at
standby mode
Dehumidify indicator
It lights when the dehumidification function is
activated
Temperature indicator
Displays the temperature setting when the Air
Conditioner is in operation
Signal receiver
caution
How to use the Remote Control
• Point the remote control to the signal receiver of
indoor unit.
• Make sure there is no obstacle that may interfere
with the signal.
Location of the remote control
Battery installation/replacement
• Slide the battery compartment cover off and
insert two new alkaline dry batteries
(2x AAA1.5Volt). Make sure that the polarity of
(+) or (-) is installed correctly.
• Slide the battery compartment cover back on
7
Remote Control
tips and information
• When changing batteries, do not use old
or varied ones, otherwise, it may cause
problems with the remote control.
• If the remote control is not used for a long
time, remove the batteries as old batteries
may leak or corrode and damage the remote
control.
• The battery life during normal use is about six
months.
• If the remote control does not operate
normally, please remove and refit the
batteries. If abnormal operation continues,
replace with new batteries.
8m
• Keep the remote control where its signal
can reach the receiver of the indoor unit (a
maximum distance of 8m is allowed).
• When you select the timer operation, the
remote control automatically transmits a signal
to the indoor unit at the specified time.
• The air conditioner will not operate if curtains,
doors or other materials block the signals from
the remote control to the indoor unit.
• Prevent any liquid from falling into the remote
control. Do not expose the remote control to
direct sunlight or heat.
• If the infrared signal receiver on the indoor
unit is exposed to direct sunlight, the air
conditioner may not function properly. Use
curtains to prevent the sunlight from falling on
the receiver.
• If other electrical appliances react to the
remote control, either move these appliances
or consult your local dealer.
Indoor Unit Display
Signal
receiver
• If you keep the remote control in a position that
hinders proper signal transmission, a time lag of
up to 15 minutes may occur.
• When the remote control sends out a signal, the
symbol will blink for about 1 second on the
display. The indoor unit will acknowledge the
signal with a beep when it receives an effective
signal. I Feel indicator
It lights when I Feel function is activated.
Turbo indicator
Illuminates during Turbo operation.
Eco (Economy) indicator
Illuminates when ECO function is in operation.
Temperature indicator
Displays the temperature settings when the air
conditioner is in operation.
Timer indicator
The indicator illuminates when Timer is set ON
and/or OFF.
Swing indicator
It lights when the Swing function is activated.
caution
How to use the Remote Control
• Point the remote control to the signal receiver of
indoor unit.
• Make sure there is no obstacle that may interfere
with the signal.
Location of the remote control
Battery installation/replacement
• Slide the battery compartment cover off and
insert two new alkaline dry batteries
(2x AAA1.5Volt). Make sure that the polarity of
(+) or (-) is installed correctly.
• Slide the battery compartment cover back on
Light
Turbo
Timer-On Temp
Timer-Off
Swing I feel Eco
Fan
Clock
Mode