John Deere 318 User Manual
John Deere Gardening equipment
Advertising
Table of contents
Document Outline
- TM1590 - 316,318,420 Lawn & Garden Tractors
- CONTENTS
- Section 10 - GENERAL INFORMATION
- Safety
- RECOGNIZE SAFETY INFORMATION
- UNDERSTAND SIGNAL WORDS
- FOLLOW SAFETY INSTRUCTIONS
- HANDLE FLUIDS SAFELY—AVOID FIRES
- PREVENT BATTERY EXPLOSIONS
- PREPARE FOR EMERGENCIES
- PREVENT ACID BURNS
- HANDLE CHEMICAL PRODUCTS SAFELY
- AVOID HIGH-PRESSURE FLUIDS
- PREPARE MACHINE FOR REPAIR
- SUPPORT MACHINE PROPERLY
- WEAR PROTECTIVE CLOTHING
- WORK IN CLEAN AREA
- SERVICE MACHINES SAFELY
- WORK IN VENTILATED AREA
- ILLUMINATE WORK AREA SAFELY
- REPLACE SAFETY SIGNS
- USE PROPER LIFTING EQUIPMENT
- REMOVE PAINT BEFORE WELDING OR HEATING
- AVOID HEATING NEAR PRESSURIZED FLUID LINES
- SERVICE TIRES SAFELY
- AVOID HARMFUL ASBESTOS DUST
- PRACTICE SAFE MAINTENANCE
- USE PROPER TOOLS
- DISPOSE OF WASTE PROPERLY
- LIVE WITH SAFETY
- General Specifications
- Repair Specifications
- REPAIR SPECIFICATIONS
- METRIC BOLT AND CAP SCREW TORQUE VALUES
- UNIFIED INCH BOLT AND CAP SCREW TORQUE VALUES
- METRIC CAP SCREW TORQUE VALUES—GRADE 7
- SERVICE RECOMMENDATIONS FOR O-RING BOSS FITTINGS
- SERVICE RECOMMENDATIONS FOR FLAT FACE O-RING SEAL FITTINGS
- TUBE AND HOSE FITTING, 37˚ FLARE AND 30˚ CONE SEAT CONNECTOR SERVICE RECOMMENDATIONS
- Test and Adjustment Specifications
- Fuels and Lubricants
- Serial Number Locations
- Safety
- Section 20 - ENGINE REPAIR
- Section 40 - ELECTRICAL REPAIR
- Section 50 - POWER TRAIN REPAIR
- Transmission
- SERVICE PARTS KITS
- REMOVE AND INSTALL CHARGE PUMP
- DISASSEMBLE AND INSPECT CHARGE PUMP
- ASSEMBLE CHARGE PUMP
- REMOVE AND INSTALL CHARGE RELIEF VALVE
- REMOVE AND INSTALL IMPLEMENT RELIEF VALVE
- REMOVE TRANSMISSION
- DISASSEMBLE TRANSMISSION COVER
- DISASSEMBLE PUMP AND MOTOR
- DISASSEMBLE PUMP AND MOTOR HOUSING
- ASSEMBLE PUMP AND MOTOR HOUSING
- ASSEMBLE PUMP AND MOTOR
- ASSEMBLE TRANSMISSION COVER
- INSTALL TRANSMISSION
- Transmission Control Linkage
- INSPECT AND REPAIR TRANSMISSION CONTROL LINKAGE—VERSION ONE (ALL MODELS)
- INSPECT AND REPAIR TRANSMISSION CONTROL LINKAGE—VERSION TWO (316 AND 318)
- INSPECT AND REPAIR TRANSMISSION CONTROL LINKAGE—VERSION TWO (420)
- INSPECT AND REPAIR TRANSMISSION CONTROL LINKAGE—VERSION THREE (ALL MODELS)
- INSPECT AND REPAIR TRANSMISSION CONTROL LINKAGE—VERSION FOUR (ALL MODELS)
- INSPECT AND REPAIR DIFFERENTIAL LOCK AND TWO-SPEED CONTROL LINKAGE (420)
- Differential
- Rear Axles
- Drive Shaft
- Transmission
- Section 60 - STEERING AND BRAKE REPAIR
- Section 70 - HYDRAULIC REPAIR
- Hydraulic Control Valve
- SERVICE PARTS KITS
- REMOVE AND INSTALL HYDRAULIC CONTROL VALVE—316 AND 318
- REMOVE AND INSTALL HYDRAULIC CONTROL VALVE—420
- DISASSEMBLE, INSPECT AND ASSEMBLE HYDRAULIC CONTROL VALVE—SINGLE-SPOOL
- DISASSEMBLE, INSPECT AND ASSEMBLE HYDRAULIC CONTROL VALVE—TWO-SPOOL
- DISASSEMBLE, INSPECT AND ASSEMBLE HYDRAULIC CONTROL VALVE—THREE-SPOOL
- Hydraulic Control Valve
- Section 80 - MISCELLANEOUS REPAIR
- Front Axle
- SPECIAL OR ESSENTIAL TOOLS
- REMOVE AND INSTALL FRONT AXLE—316 AND 318
- INSPECT AND REPLACE PIVOT BUSHINGS—316 AND 318
- REMOVE FRONT AXLE—420
- DISASSEMBLE AND INSPECT PIVOT PIN—420
- ASSEMBLE PIVOT PIN—420
- INSTALL FRONT AXLE—420
- REMOVE AND INSTALL SPINDLES
- INSPECT AND REPLACE SPINDLE BUSHINGS
- INSPECT AND REPLACE WHEEL BEARINGS
- ADJUST TOE-IN
- Mower Spindle and Jack Sheave Repair
- Mower Gear Case Repair
- DISASSEMBLE AND INSPECT MOWER GEAR CASE—50-INCH MOWER
- ASSEMBLE MOWER GEAR CASE—50-INCH MOWER
- DISASSEMBLE AND INSPECT MOWER GEAR CASE—EARLY 60-INCH MOWER (CURTIS)
- ASSEMBLE MOWER GEAR CASE—EARLY 60-INCH MOWER (CURTIS)
- DISASSEMBLE AND INSPECT MOWER GEAR CASE—LATER 60-INCH MOWER (PEERLESS)
- ASSEMBLE MOWER GEAR CASE—LATER 60-INCH MOWER (PEERLESS)
- DISASSEMBLE AND INSPECT MOWER GEAR CASE—260 ROTARY MOWER
- ASSEMBLE MOWER GEAR CASE—260 ROTARY MOWER
- Front Axle
- Section 220 - ENGINE, FUEL AND AIR SYSTEM CHECKOUT AND DIAGNOSIS
- Section 240 - ELECTRICAL CHECKOUT, OPERATION AND DIAGNOSIS
- Section 250 - POWER TRAIN CHECKOUT, OPERATION AND DIAGNOSIS
- Section 260 - STEERING AND BRAKES CHECKOUT, OPERATION AND DIAGNOSIS
- Section 270 - HYDRAULIC SYSTEM CHECKOUT, OPERATION AND DIAGNOSIS
- Section 299 - DEALER FABRICATED TOOLS
- Index