Sony STR- D915 User Manual
Fm stereo fm-am receiver
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Advertising
Table of contents
Document Outline
- FM Stereo FM-AM Receiver
- Warning
- Note to CATV system installer
- Owner's Record
- For the customers In Canada
- r— CAUTION:
- TV/video programs
- Tuner
- DOLBY* PRO LOGIC
- Sound field (combination of digital delayed surround and tone controls)
- Remote commander
- On safety
- On operation
- To prevent internal heat buildup in the unit,
- Do not install the unit:
- Do not place anything on top of the cabinet.
- On cleaning the cabinet
- For the customers in the U.S.A.
- Do not throw away the carton and packing material!
- Open the cover.
- To avoid damage caused by battery leakage and corrosion
- Battery life
- AM antenna extension
- On the IMPEDANCE selector (STR-D915 only)
- Note
- Note
- Caution
- IMPORTANT
- Adjusting volume
- Listening toAAAatching a Program Source
- 1 Select the program source (except TUNER).
- 2 Press DISPLAY if "INDEX MODE* is not displayed.
- 3 Press DPC MODE repeatedly until the INDEX indicator lights up.
- If you input an already stored source under any other index name
- To switch the original function name display and created index name display
- To change the turn-off time
- To check the remaining time of the sleep timer
- Press TUNER.
- Press FM/AM to select FM or AM.
- Press DIRECT.
- Note on AM tuning
- To correct the entered frequency
- If you enter a frequency not covered by the tuning interval
- When the entered frequency does not exist in the receivable frequency range
- When an FM stereo program is noisy
- Press TUNER.
- 3 Press DISPLAY if the frequency is not dispiayed.
- 4 Press INDEX SELECT/TUNING + or -.
- ' the automatic scan stops frequently or FM reception only)
- Press TUNER.
- Tune in the desired station.
- 4 Press SHIFT to select the memory page (A, B or C) while "MEMORY” is displayed.
- 5 Press the desired numeric button (1 to 0) while "MEMORY" is displayed.
- Use of memory pages
- Replacing a preset station
- IMPORTANT
- Press TUNER.
- 2 Press SHIFT to select the memory page (A, B, or C).
- 3 Press the numeric buttons jto designate the desired preset station number.
- Press TUNER.
- 2 Press DISPLAY if the frequency is not displayed.
- 3 Press PRESET TUNING + or-to select the desired preset station.
- Press TUNER.
- Press DISPLAY to set to the INDEX mode.
- Select the desired station.
- Turn on the monitor TV.
- Select the desired program on the TV tuner or the VCR.
- Remote Controls
- Operative buttons
- Turning on the power of each equipment
- Press one of the SYSTEM CONTROL/FUNCTION buttons.
- 2 Operate the units with each button.
- Turning off the power of equipments
- If you use Sony TV
- If you use TV most of the time (Only for Sony TV)
- Back ground operation
- Note
- Note
- PHANTOM mode
- 3CH (Channel) LOGIC mode
- NORMAL mode
- Press TEST TONE on the remote commander to set to off.
- Sequence of the test tone
- 1 Press SOUND FIELD ON/OFF to ON.
- 2 Press SOUND FIELD MODE repeatedly until DOLBY SUR indicator lights.
- 4 Press TEST TONE on the remote commander.
- — for DOLBY SUR (Dolby surround) mode
- 1 Press SOUND FIELD ON/OFP to ON.
- 2 Press SOUND FIELD MODE repeatedly until the DOLBY SUR indicator lights.
- 3 Press DPC MODE repeatedly until the SUR (surround) indicator lights.
- Press A or V to select the delay time mode.
- Press < or > to adjust the delay time.
- To turn off the surround effect
- Note
- Adjusting the delay time of the rear speakers
- Restoring to the setting stored at the factory
- (For U.S.A. and Canadian models)
- Amplifier section
- (For Australian model)
- Amplifier section
- FM tuner section
- AM tuner section
- Video section
- General
- Identifying the Parts and Controls
- Quick Reference
- Quick Reference
- Warning