Petsafe UltraSmart® In-Ground Fence™ - Manual (Page 26)

26 Customer Care Center 1-800-732-2677
3. Bend the leads of the RF Choke into the shape shown (14A).
4. Carefully wrap the RF Choke leads around the Boundary Wire leads
as shown (14B).
5. Re-insert the Boundary Wire and RF Choke leads into the Loop
Terminals on the Surge Protector or Transmitter.
6. Plug the Power Adapter back into the Transmitter Power Jack.
7. Adjust the portable AM radio between the 530 to 600 KHz AM
bands (where there are no active radio stations).
14A 14B
8. Adjust the transmitter Field Width knob high enough to obtain a signal on the portable radio when holding the radio
over the containment Boundary Wire. The signal you hear on the radio is short static pulses. Remember that the signal
should be absent on any twisted wire sections because twisting the wire cancels the signal.
9. Hold the radio 1 to 2 feet off of the ground and swing the radio (side to side, left to right) over the wire as you walk
along the boundary.
10. If the pulsating static stops, weakens or changes pitch, mark the spot with a flag or stick. No sound indicates a complete
break in the wire. If the signal fades or changes in pitch, look for a nick in the wire insulation.
11. Continue around the remaining boundary and mark any additional signal change with a flag or stick.
12. After completing the entire boundary, return to the marked spots. Examine the wire for 3 to 4 feet in each direction.
13. Replace the damaged Boundary Wire using the same gauge wire used in the original installation and use waterproof
splice capsules to make the connections. Contact the Customer Care Center for additional Boundary Wire, Wire Nuts
and Waterproof Splice Capsules, if needed.
Option 3: Follow the procedure below:
1. Unplug the Fence Transmitter.
2. Connect both ends of your twisted Boundary Wire to one Loop Wire Terminal.
3. Measure and cut a Test Wire which is half the length of your total Boundary Wire footage.
4. Connect one end of Test Wire to the other Loop Wire Terminal.
5. Locate the halfway point of your boundary and cut the Boundary Wire.
6. Splice the other end of the Test Wire to either side of your Boundary Wire where you cut it in half.
7. Plug in the Fence Transmitter and check the Status Indicator Light. If the Status Indicator Light glows solid green, you can
assume the break is in the other half of the Boundary Wire.
8. If the Status Indicator Light flashes red and the alarm sounds, you may assume there is a break in this portion of the
Boundary Wire. However, there is a small chance of having more than one break in your system. Be sure to check both
halves of your entire loop.
9. Replace the damaged Boundary Wire with new Boundary Wire.
10. Reconnect the Boundary Wire to the Fence Transmitter.
11. Check the Status Indicator Light. If the Status Indicator Light glows solid green, test the system with the Receiver Collar.
Terms of Use and Limitation of Liability
1. Terms of Use
This Product is offered to you conditioned upon your acceptance without modification of the terms,
conditions and notices contained herein. Usage of this Product implies acceptance of all such terms,
conditions, and notices.
2. Proper Use
This Product is designed for use with pets where training is desired. The specific temperament of your pet
may not work with this Product. We recommend that you not use this Product if your pet is less than 8
pounds or if your pet is aggressive. If you are unsure whether this is appropriate for your pet, please consult
your veterinarian or certified trainer.
Proper use includes reviewing the entire Guide provided with your Product and any specific Caution
statements.
3. No Unlawful or Prohibited Use
This Product is designed for use with pets only. This pet training device is not intended to harm, injure or
provoke. Using this Product in a way that is not intended could result in violation of Federal, State or local laws.
4. Limitation of Liability
In no event shall Radio Systems Corporation ® be liable for any direct, indirect, punitive, incidental, special or
consequential damages, or any damages whatsoever arising out of or connected with the use or misuse of
this Product. Buyer assumes all risks and liability from the use of this Product.
5. Modification of Terms and Conditions
Radio Systems Corporation ® reserves the right to change the terms, conditions and notices under which this
Product is offered.