KEYENCE LJ-V7000 Series - Manual (Page 74)

74 LJ-V7000_COM_RM_E
• Profilemask settings
<XZcorrection selection>
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:04h, Item:09h
Target1:00h (headA/wide), 01h (headB)
Target2:00h (position correction1), 01h (position
correction2), Target3~4:00h
byte Setting Data
0
XYcorrection selection: 0:OFF, 1:Xcorrection,
2:Zcorrection, 3:XZcorrection, 4:ZXcorrection,
5:Feature point correction
1 Reserved (fixed as 0)
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)
<Z correction Height measurement detail>
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:04h, Item:0Ch
Target1:00h (headA/wide), 01h (headB)
Target2:00h (position correction1), 01h (position
correction2), Target3~4:00h
byte Setting Data
0
Height measuring area Left: any value in
measurement range
(0.01μm unit Sined 32-bit integer
example: 5mm=500000)
1
2
3
4
Height measuring area Right: any value in
measurement range
(0.01μm unit Sined 32-bit integer
example: 5mm=500000)
5
6
7
8
Height type: 0:Peak, 1:bottom, 6:Average
9 Reserved (fixed as 0)
10 Reserved (fixed as 0)
11 Reserved (fixed as 0)
<Featurepoint correction detail>
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:04h, Item:0Dh
Target1:00h (headA/wide), 01h (headB)
Target2:00h (position correction1), 01h (position
correction2), Target3~4:00h
byte Setting Data
0
Correction target selection: 0:Peak, 1:Bottom,
2:Knee, 3:Intsect (lines), , 4:Contact (lin-arc)
1 Reserved (fixed as 0)
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)
* From 4byte, unique parameters are assigned to each
correction target. For details on the unique parameters,
see "Measurement area details" (page 83).
<Profile mask area settings group>
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:05h, Item:01h
Target1:00h (headA/wide), 01h (headB), Target2~4:00h
byte Setting Data
0
Area selection: 0:Disabled,
1:Rectangle, 2:Triangle
1
position correction selection: 0: No
position correction, 1:Position
correction1, 2:Position correction2
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)
4
Xcoordinate1: any value in
measurement range
(0.01μm unit Sined 32-bit integer
example: 5mm=500000)
*1
5
6
7
8
Zcoordinate1: any value in
measurement range
(0.01μm unit Sined 32-bit integer
example: 5mm=500000)
9
10
11
12
Xcoordinate2: any value in
measurement range
(0.01μm unit Sined 32-bit integer
example: 5mm=500000)
13
14
15
16
Zcoordinate2: any value in
measurement range
(0.01μm unit Sined 32-bit integer
example: 5mm=500000)
17
18
19
20
Xcoordinate3: any value in
measurement range
(0.01μm unit Sined 32-bit integer
example: 5mm=500000)
21
22
23
24
Zcoordinate3: any value in
measurement range
(0.01μm unit Sined 32-bit integer
example: 5mm=500000)
25
26
27
~
139
* When Rectangle is selected, upper left (Xcoordinate1,
Zcoordinate1) and bottom right (Xcoordinate2,
Zcoordinate2) should be set. Xcoordinate3, Zcoordinate3
is no effect.
* When Triangle is selected, (Xcoordinate1, Zcoordinate1),
(Xcoordinate2, Zcoordinate2) and (Xcoordinate3,
Zcoordinate3) are used.
* 1 the number of profile mask area (×5) is continuing.
(Total 140byte is used.)