Novak Silver Solder (55-583X-1.2) User Manual
Soldering tips, Always use a good, high-heat soldering iron
Novak R/C, Inc. California • 2014 • Made in China • 55-583X-1.2
This product contains chemicals which are known to the state of
California to cause cancer, birth defects, or other reproductive harm.
Specially formulated Lead-Free Solder with 3% Silver
content for high-conductivity, low-resistance, & strong
solder joints at a relatively low melting point.
Environmentally friendly & safe to handle--Perfect for hand soldering.
SOLDERING TIPS
Always use a good, high-heat soldering iron.
Preparing The Wire: Strip the insulation from the end
of the wire. Tightly twist the exposed strands of wire.
Apply heat to exposed wire with iron and add solder to
the tip of the iron and to exposed wire at the same time.
Soldering The Wire: Pre-tin the surface being soldered
to. Place stripped & tinned end of wire on surface and
heat with iron--add just enough solder to form a clean
and continuous joint from the surface up onto the wire.
IMPORTANT NOTE
PROLONGED/EXCESSIVE HEATING WILL DAMAGE PC BOARDS
- Brushless Speed Control: Crusher Basic Set-Up (original) (55-1833-1 Rev.2) (2 pages)
- Brushless Speed Control: Crusher Basic Set-Up (w/Simple-Tuner) (55-1834-1 Rev.1) (2 pages)
- Brushless Speed Control: Crusher Field Guide (Crawler Mode) --- Simple-Tuner Version ESC (4) (4 pages)
- Brushless Speed Control: Crusher Field Guide (Standard Modes) --- Simple-Tuner Version ESC (1) (4 pages)
- Brushless Speed Control: Crusher Field Guide -- Original Version (55-1833P-1 Rev.2) (4 pages)
- Brushless Speed Control: Crusher Simple-Tuner Profile Cheat Sheet (14) (1 page)
- Brushless Speed Control: Drift Spec Basic Set-Up (55-3074-1 Rev.1) (2 pages)
- Brushless Speed Control: Drift Spec Track Guide (55-3074P-1 Rev.1) (2 pages)
- Brushless Speed Control: Edge 2S (55-1851-1 Rev.2) (2 pages)
- Brushless Speed Control: Edge Programming Guide (55-1851P-1.7 Rev.7) (2 pages)
- Brushless Speed Control: GTB 3 Basic Set-Up (55-1747-1.2) (2 pages)
- Brushless Speed Control: GTB 3 Track Guide (55-1747P-1.1) (4 pages)
- Brushless Speed Control: Impact Basic Set-Up (55-1730-1 Rev.3) (2 pages)
- Brushless Speed Control: Impact Track Guide (55-1730P-1 Rev.2) (2 pages)
- Brushless Speed Control: Pulse V2 Basic Set-Up (55-1756-2 Rev.2) (2 pages)
- Brushless Speed Control: Pulse V2 Track guide (55-1755P-2 Rev.1) (2 pages)
- Brushless Speed Control: Super-Tuner Brain Board Upgrade Track Guide (55-1746P-1 Rev.2) (2 pages)
- Brushless Speed Control: Timbuk2 Basic Set-Up (55-1832-1 Rev.4) (2 pages)
- Brushless Speed Control: Timbuk2 Field Guide (55-1832P-1 Rev.5) (2 pages)
- Brushed Speed Control: Eiger & Eiger Pro Basic Set-Up Guide (55-1835-1 Rev.6) (2 pages)
- Brushed Speed Control: Eiger & Eiger Pro Field Guide-- NEW version ESCs (standard height heat sinks) (55-1835P-1.4) (4 pages)
- Brushed Speed Control: Eiger & Eiger Pro -- V1 (low profile heat sinks) (55-1835-1.2) (2 pages)
- Brushed Speed Control: M2 Dig Basic Set-Up Guide (55-1846-1.3) (2 pages)
- Brushed Speed Control: M2 Dig Basic Set-Up Guide- 4 Profile Model (55-1846-1.4) (2 pages)
- Brushed Speed Control: M2 Dig Field Guide (55-1846P-1 Rev. 1.1) (4 pages)
- Brushed Speed Control: M2 Dig Field Guide- 4 Profile Model (55-1846P-1 Rev. 1.2) (4 pages)
- Brushless Motor: 4PHD Heavy-Duty 4-Pole BL Motor (55-3510M-1 Rev.1) (2 pages)
- Brushless Motor: 55-5980-1.C__Manufacturing 3-Up Layout (2 pages)
- Brushless Motor: 55-5984-1.D__Manufacturing 6-Up Layout (55-5984-1.D) (2 pages)
- Brushless Motor: 55-6801-1.D__Manufacturing 6-Up Layout (55-6801-1.D) (2 pages)
- Brushless Motor: Ballistic 540/550 Motor (2 pages)
- Brushless Motor: Brushless Motor Rotor and End Bell/Bearing Replacement (2 pages)
- Brushless Motor: Brushless Motor Stator Replacement (55-6801-1.D) (1 page)
- Brushless Motor: Brushless Motor Timing/Sensor Assembly Replacement (55-5984-1.D) (1 page)
- Brushless Motor: Brushless Sensor Harness Removal & Replacement (55-535X-1) (1 page)
- Brushless Motor: Drift Spec Motor (55-3074M-1 Rev.1) (2 pages)
- Brushless Motor: Vulcan Motor (55-3640-1 Rev.3) (2 pages)
- Brushed Motor: Rock Star Motor (55-3557-1 Rev.C) (2 pages)
- Brushed Motor: Terra Claw Motor (55-3556-1 Rev.C) (2 pages)
- 1S LiPo Booster Module (1 page)
- 4PHD Motor Replacement Part (55-5956-1) (2 pages)
- 5463 3A High-Voltage BEC (55-5463-7) (2 pages)
- 55-5750-1.2_Manufacturing 9-Up Layout (55-5750-1.2) (1 page)
- 55-583X-1.2_Manufacturing 6-Up Layout (55-583X-1.2) (1 page)
- 55-5860-1.2_Manufacturing 9-Up Layout (55-5860-1.2) (1 page)