Sears 358.79828 User Manual

Sears Tools

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising

Table of contents

Document Outline

WARNING
MAINTENANCE AGREEMENT
CUSTOMER RESPONSIBILITIES
OOLS REQUIRED FOR ASSEMBLY
TO REMOVE BRUSHWACKER FROM CARTON
WARNING:
HOW TO ASSEMBLE YOUR BRUSHWACKER
- HANDLEBAR ASSEMBLY (See Fig. 1)
- THROTTLE HANDLE ASSEMBLY (See Fig. 2 )
- (See Flg.3)
CUTTING LINE HEAD CONFIGURATION
- INSTALLING UNE LnSIlTERjONTa PLASTIC UNE TRIMMER SHIELD (See Fig. 4)
- PRE-INSTALLATION
- INSTALLING THE PLASTIC UNE TRIMMER SHIELD (See Fig. 5)
- INSTALLING THE DUAL UNE HEAD (See Fig. 6 & 7 }
- RE-INSTALLATION
- ISTALUNG THE METAL BLADE SHIELD iee Fig. 8 )
- BLADE TRANSPORT/STORAGE COVER (See Figure 9)
- INSTALLING THE BRUSH TRI-BLADE (S^ Fig. 10 & 11)
SAW BLADE CONFIGURATION
- PRE-INSTALLATION
- INSTALUNG THE SAW BLADE (See Fig. 12,13, & 14 )
- CHECKLIST
KNOW YOUR BRUSHWACKER (See Fig. 16)
- STOPPING YOUR ENGINE
ÎLADE SAFETY
WARNING
11
- PERATOR SAFETY
- HT SAFETY
- CUTTING SAFETY
BLADE SAFETY
- WHAT CAUSES BLADE THRUST?
- WHEN DOES BLADE THRUST OCCUR?
- REDUCE THE CHANCE OF BLADE THRUST
- OPERATING/USE TIPS (Figure 20)
UNE TRIMMER SAFETY
WARNING:
- OPERATOR SAFETY
- CUTTING SAFETY
- UNIT SAFETY
DIMMER LINE ADVANCE (Fig. 21 )
- 1g. 22,23,24,25, & 26)
WARNING:
BEFORE STARTING ENGINE:
- GASOLINE
- FUEL STABILIZER
- 2-CYCLE OIL:
- GASOUNE AND OIL MI3tTURE
- FUEL MIXTURE CHART
TOPPING YOUR ENGINE
TARTING YOUR ENGINE (Fig. 27)
WARNING:
- SFORE STARTING THE ENGINE:
- 'ARTING A COLD ENGINE OR WARM ENGINE AFTER RUNNING OUT OF FUEL:
- STARTING A WARM ENGINE THAT HAS NOT RUN OUT OF FUEL
- STARTING A FLOODED ENGINE:
MAINTENANCE SCHEDULE
GENERAL RECOMMENDATIONS
- CLEAN UNIT AND LABELS
BEFORE EACH USE
- CHECK FOR DAMAGED/WORN PARTS
- LUBRICATION CHART (Fig. 28)
WARNING
- iECK FOR LOOSE FASTENERS/PARTS
- CCK GEAR BOX LUBRICATION 29 )
- EAN AIR FILTER (Fig. 30 )
- REPLACE SPARK PLUG (Fig. 31 )
- INSPECT MUFFLER AND
- SPARK ARRESTOR SCREEN (IF INSTALLED)
DUAL LINE REPLACEMENT
- INSTALLING SPOOL WITH UNE ALREADY WOUND (Fig. 32,33,34,35, & 36 )
ILADE SHARPENING
- BRUSH TRI-BLADE SHARPENING (Fig. 37)
- SAW BLADE SHARPENING (Fig. 38)
- CARBURETOR PRESETS (Fig. 39)
ADJUSTING PROCEDURE
- IDLE SPEED ADJUSTMENT
- LOW SPEED MIXTURE ADJUSTMENT
- HIGH SPEED MIXTURE ADJUSTMENT
- ACCELERATION CHECK
WARNING:
- AS TRIMMER/BRUSHCUTTER STORAGE JNSTRUCTIONS
- ENGINE
- OTHER
TROUBLE SHOOTING CHART
SEAES BEUSHWACKER™ - MODEL 368.798280
SEARS BRUSHWACKER™ - MODEL 358.798280
SEARS BRUSHWACKER™ - MODEL 358,798280
SEARS BR0SHWACKER"- - MODEL 3S8.798280 CARBURETOR ASSY. - PART NO. 503-281505
SEARS BRUSHWACiOER“ - MODEL 358.798280
CRflFTSMflN^
- Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA