Aiwa CX-ZL10 - Manual (Page 17)

SEniNG THE TIME
The unit can be turned on at a specified time every day with the
built-in timer.
Preparation
Make sure the clock is set correctly.
1 Press one of the function buttons to select a
source.
• If TUNER/BAND is pressed, the band can be selected in
this step.
2 Press TIMER while pressing SHIFT on the remote
control until © and “S PLAY” appear on the
display.
Time and audio source name flash alternately.
^ fBASS ROCK POP CLASSIC
.... k______________
3 Within 6 seconds, press ◄◄ or ►► to designate
the timer-on time, then press II.
Holding these buttons down will vary the time rapidly.
Ш ............ r-8ASS ROCK POP CLASSIC I© f
w-------------------------------- /
= I1HM lP;nn
6 Prepare the source.
To listen to a CD, load the disc to be played first on tray 1.
To listen to a tape, insert the tape into Deck 1 or 2.
To listen to the radio, tune in to a station.
7 Press POWER to turn off the power.
© remains on the display after the power is turned off (timer
standby mode).
!■ .■'!
■j. f-! f
• i ■ ■ ■
fiC
Ul
H
o
z
4
¡i
o
8 Get ready for the TAPE function or the timer
recording.
To listen to the tape, press ► on Deck 1 or 2.
To record the source, insert the tape into Deck 1 and press
• on Deck 1.
When the timer-on time is reached, the unit turns on and
begins play with the selected source.
NOTE
You can change the source that was selected in step 1 by
pressing one of fhe function buttons before pressing II in step
3.
The timer recording period and tape length
When the length of the tape to be recorded is shorter than the
timer recording period, • on Deck 1 is released before the timer
is off.
When the tape length is longer than the timer recording period,
• is not released. If • is not released for a long time, the tape
in the deck may be damaged. Press to release •.
To check the timer setting
Press TIMER while pressing SHIFT.
The selected source, the timer-on time, and the duration for the
timer-activated period will be displayed for 4 seconds.
To change any of the previous setting
Carry out from step 1.
However, if you do not change the timer-on time, in step 3 just
press II twice and continue from step 4.
To cancel the timer standby mode temporarily
Press TIMER while pressing SHIFT so that 0 disappears.
To restore the timer standby mode, press these buttons again to
display 0.
4 Within 4 seconds, press ◄◄ or ►► to select the
duration for the timer-activated period.
The duration can be set between 5 and 240 minutes in 5-
minute steps.
' : /i
■ !
ROCK POP cussic I q
i _ : \
<«3
The duration will be automatically set atter 4 seconds, it will
also be set if I I is pressed within 4 seconds atter step 4.
5 Adjust the volume.
The source sound will play at the volume level set in this step
when the power is turned on by the timer.
If the volume level is set to 17 or higher, however, it will
automatically be set to 16 when the power is turned on.
Using the unit while the timer is set
You can use the unit normally after setting the timer.
Before turning off the power, carry out step 5 and 6.
NOTE
- Timer playback and timer recording will not begin unless the
power is turned off.
■ Connected equipment cannot be turned on and off by the built-
in timer of this unit. Use an external timer.
• While the timer is in operation, the display indication is dimmer
than usual.
ENGLISH
17