CRU DataPort 10 Secure 256-bit - Manual

RTX220 QR - Manual
DataPort ® 10 Secure Quick Start Guide
1. Installation Steps
1.1 Receiving Frame Installation
a. Slide the receiving frame into an open 5.25” bay.
b. Secure the receiving frame to the chassis with the four screws provided.
c. Attach the SATA data cable to the SATA port on the rear of the receiving frame and the
other end to the corresponding SATA port on the computer’s motherboard.
d. Attach the SATA power connectors to the SATA power port on the rear of the receiving
frame. If no SATA power connectors are available, attach the included Molex-to-SATA
adapter cable to a Molex power plug. Then plug the SATA end of the adapter cable
into the rear of the receiving frame.
1.2 Hard Drive Installation
a. If the carrier is bundled with a frame, use the included DataPort Key to unlock the
carrier and then remove it from the frame.
b. Use a Phillips-head screwdriver to remove the screw securing the carrier cover to the
back of the carrier, then slide the cover off.
Product Warranty
CRU-DataPort (CRU) warrants this product to be free of significant defects in material and workmanship for a period of three years from the original date of purchase. CRU’s
warranty is nontransferable and is limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other warranties. CRU expressly disclaims all other warranties, including but not limited to, the implied warranties of mer-
chantability and fitness for a particular purpose and non-infringement of third-party rights with respect to the documentation and hardware. No CRU dealer, agent, or employee
is authorized to make any modification, extension, or addition to this warranty. In no event will CRU or its suppliers be liable for any costs of procurement of substitute products
or services, lost profits, loss of information or data, computer malfunction, or any other special, indirect, consequential, or incidental damages arising in any way out of the sale
of, use of, or inability to use any CRU product or service, even if CRU has been advised of the possibility of such damages. In no case shall CRU’s liability exceed the actual money
paid for the products at issue. CRU reserves the right to make modifications and additions to this product without notice or taking on additional liability.
FCC Compliance Statement: “This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a home or commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
In the event that you experience Radio Frequency Interference, you should take the following steps to resolve the problem:
1) Ensure that the case of your attached drive is grounded.
2) Use a data cable with RFI reducing ferrites on each end.
3) Use a power supply with an RFI reducing ferrite approximately 5 inches from the DC plug.
4) Reorient or relocate the receiving antenna.
A6-010-0002-1 Revision 1.2
Product Names DataPort 10 Secure
Interface Types & Speeds SATA: up to 150 Mbps
Compatibility 2.5” SATA Hard Drives
3.5” SATA Hard Drives
Data Connectors One (1) SATA connector
Encryption 128-bit AES (Advanced Encryption Standard) or 256-bit AES (Advanced Encryption Standard)
128-bit and 256-bit encryption are not cross-compatible
Connector Insertion Rating 25,000+ Carrier-to-Frame
Operating System
Requirements • Windows 7, Vista, or XP
• Mac OS X
• Linux distributions that support SATA, USB, or FireWire 800
Compliance EMI Standard: FCC Part 15 Class B, CE
EMC Standard: EN55022, EN55024
FIPS: FIPS 140-2, FIPS PUB 197
Shipping Weight 3.00 pounds (includes accessories)
Product Dimensions 5.75” x 7.87” x 1.61” (146mm x 200mm x 41mm)
Warranty 3-year limited warranty. See warranty statement for details and limitations.
We don’t expect anything to go wrong with your CRU-DataPort product. But if it does,
Tech Support is standing by and ready to help. Contact us at http://www.cru-dataport.
com/technical-support/customer-technical-support.php
Visit http://www.cru-dataport.com/technical-support/product-manuals.php
to download a copy of the complete User Manual.
FOR HOME OR OFFICE USE
Models Covered:
DataPort 10 Secure with AES 128
DataPort 10 Secure with AES 256