Display of the clamping system, Rotating / replacing the cutting stick – Formax Cut-True 27A User Manual
Page 15
12
Display of the Clamping System
This function allows you to see the movements of the paper clamping system. Press the Clamp Status icon.
Stage 1:
The clamping bar
lowers when you
press both of the
green clamp enable
buttons.
Stage 2:
The clamping bar is
holding the stack of
paper securely.
Stage 3:
The clamping bar
is going up when
you push either of
the clamp enable
buttons.
Stage 4:
The clamping bar
is in its original
position.
ROTATING / REPLACING THE CUTTING STICK
The cutting stick is the surface the blade contacts during the cutting process. It can be rotated and used on each side,
4 times altogether.
If the last piece of paper in the stack is not cut through cleanly, and the blade depth has been adjusted properly, the cut-
ting stick should be rotated or replaced.
The cutting stick sits in a channel in the base of the cutter, just below the blade carrier. To remove it, first turn off the
power. Then insert the 5mm screwdriver into the cutting stick access slot (see photo below left) and lift up. Grasp the
cutting stick and remove (see photo below right). Rotate the cutting stick to a new side and re-install.
NOTE: When the cutting stick is rotated or replaced, the blade height must be readjusted. See the next page for blade
height adjustment instructions.
- FD 1500 Plus
- FD 1500 Plus
- FD 1500 Plus
- FD 1500 Plus
- FD 1500 Plus
- FD 1202
- FD 1202
- FD 2030 Quick Setup Guide & Test Sheet
- FD 2030 Quick Setup Guide & Test Sheet
- FD 2030 Quick Setup Guide & Test Sheet
- FD 2030 Quick Setup Guide & Test Sheet
- FD 1502 Plus
- FD 2052 Operator Manual, 4th Edition
- FE 2032
- FD 2000IL System
- FD 2052 Quick Setup Guide & Test Sheet
- FD 2052IL System
- FD 382 / FD 38X
- FD 382 / FD 38X
- FD 2082
- FD 6100
- FD 2084
- 2200 Series
- FD 6102
- 6202 Series
- 6200 (600) Series
- 6302 Series
- 6304 Series
- 6402 Series
- 6600 Series
- 6206 Series
- 6204 Series
- 6900 Series
- 7100 Series
- 6606 Series
- 6404 Series
- FD 314
- FD 314
- FD 305
- FD 312
- FD 320
- FD 332
- 7102/7102XT Series
- 7200 Series
- FD 372
- FD 340
- FD 380
- FD 342
- FD 3200
- FD 120
- FD 125
- FD 4170
- FD 4400
- FD 540
- FD 670
- Cut-True 13M
- Cut-True 16M
- Cut-True 16M
- Cut-True 22S
- FD 210M
- Cut-True 27S
- FD 215S
- FD 230
- FD 260-10
- FD 260
- FD 260-20
- FD 280
- FD 280-10
- FD 130
- FD 452
- FD 280-20
- 402 Series
- 402 Series, Rev. 2
- FD 150
- FD 402A1 Operator Manual
- FD 402TA1
- FD 160
- FD 404A1 Operator / Parts Manual
- V-STACK36
- Roller Cleaning Kit Instructions
- FD 180
- FD 4060