Asus P5B-VM DO - Manual (Page 46)

1-34 Chapter 1: Product introduction
4. ICH8DO Serial ATA connectors (7-pin SATA1[red], SATA2 [red], SATA3
[red], SATA4 [red], SATA5 [black], SATA6 [black])
These connectors are for the Serial ATA signal cables for Serial ATA hard disk
drives.
Connect the right-angle side
of SATA signal cable to SATA
device. Or you may connect the
right-angle side of SATA cable to
the onboard SATA port to avoid
mechanical conflict with huge
graphics cards.
right angle side
R
G
ND
RS
AT
A_
TX
P3
RS
AT
A_
TX
N3
G
ND
RS
AT
A_
RX
P3
RS
AT
A_
RX
N3
G
ND
G
ND
RS
AT
A_
TX
P4
RS
AT
A_
TX
N4
G
ND
RS
AT
A_
RX
P4
RS
AT
A_
RX
N4
G
ND
SATA3 SATA4
G
ND
RS
AT
A_
TX
P5
RS
AT
A_
TX
N5
G
ND
RS
AT
A_
RX
P5
RS
AT
A_
RX
N5
G
ND
G
ND
RS
AT
A_
TX
P6
RS
AT
A_
TX
N6
G
ND
RS
AT
A_
RX
P6
RS
AT
A_
RX
N6
G
ND
SATA5 SATA6
G
ND
RS
AT
A_
TX
P1
RS
AT
A_
TX
N1
G
ND
RS
AT
A_
RX
P1
RS
AT
A_
RX
N1
G
ND
G
ND
RS
AT
A_
TX
P2
RS
AT
A_
TX
N2
G
ND
RS
AT
A_
RX
P2
RS
AT
A_
RX
N2
G
ND
SATA1 SATA2
P5B-VM DO
P5B-VM DO SATA connectors
R
G
ND
RS
AT
A_
TX
P3
RS
AT
A_
TX
N3
G
ND
RS
AT
A_
RX
P3
RS
AT
A_
RX
N3
G
ND
G
ND
RS
AT
A_
TX
P4
RS
AT
A_
TX
N4
G
ND
RS
AT
A_
RX
P4
RS
AT
A_
RX
N4
G
ND
SATA3 SATA4
G
ND
RS
AT
A_
TX
P5
RS
AT
A_
TX
N5
G
ND
RS
AT
A_
RX
P5
RS
AT
A_
RX
N5
G
ND
G
ND
RS
AT
A_
TX
P6
RS
AT
A_
TX
N6
G
ND
RS
AT
A_
RX
P6
RS
AT
A_
RX
N6
G
ND
SATA5 SATA6
G
ND
RS
AT
A_
TX
P1
RS
AT
A_
TX
N1
G
ND
RS
AT
A_
RX
P1
RS
AT
A_
RX
N1
G
ND
G
ND
RS
AT
A_
TX
P2
RS
AT
A_
TX
N2
G
ND
RS
AT
A_
RX
P2
RS
AT
A_
RX
N2
G
ND
SATA1 SATA2
P5B-VM DO
P5B-VM DO SATA connectors
R
G
ND
RS
AT
A_
TX
P3
RS
AT
A_
TX
N3
G
ND
RS
AT
A_
RX
P3
RS
AT
A_
RX
N3
G
ND
G
ND
RS
AT
A_
TX
P4
RS
AT
A_
TX
N4
G
ND
RS
AT
A_
RX
P4
RS
AT
A_
RX
N4
G
ND
SATA3 SATA4
G
ND RS
AT
A_
TX
P5
RS
AT
A_
TX
N5
G ND RS
AT
A_
RX
P5
RS
AT
A_
RX
N5
G ND
G
ND RS
AT
A_
TX
P6
RS
AT
A_
TX
N6
G ND RS
AT
A_
RX
P6
RS
AT
A_
RX
N6
G ND
SATA5 SATA6
G
ND RS
AT
A_
TX
P1
RS
AT
A_
TX
N1
G ND RS
AT
A_
RX
P1
RS
AT
A_
RX
N1
G ND
G
ND RS
AT
A_
TX
P2
RS
AT
A_
TX
N2
G ND RS
AT
A_
RX
P2
RS
AT
A_
RX
N2
G ND
SATA1 SATA2
P5B-VM DO
P5B-VM DO SATA connectors
5. IEEE 1394a port connector (10-1 pin IE1394_2)
This connector is for a IEEE 1394a port. Connect the IEEE 1394a module
cable to this connector, then install the module to a slot opening at the back
of the system chassis.
R
P5B-VM DO IEEE 1394a Connector
P5B-VM DO
IE1394_2
1
GND +12V TPB1- GND TP
A1-
+12V
TPB1+
GND
TP
A1+
The IEEE 1394a module is purchased separately.